Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Crosslinked Polyethylene (PEX) Pipe for Gas Distribution Applications
Přeložit název
NORMA vydána dne 1.5.2021
Označení normy: ASTM F2968/F2968M-21
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2021
Kód zboží: NS-1024087
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Trubky z plastické hmoty
Potrubí a potrubní spojky
Systémy dodávky plynu v budovách
Keywords:
crosslinked polyethylene, gas distribution, HDB, hydrostatic stress, metric, PEX, pipe, PPI, pressure,, ICS Number Code 23.040.20 (Plastic pipes),23.100.40 (Piping and coupling),91.140.40 (Gas supply systems)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||
1.1?This specification covers outside diameter controlled, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe, made in pipe dimension ratios ranging from 6 to 17, and pressure rated for gas distribution. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, minimum operating temperature and squeeze-off. Requirements for pipe markings are also given. The pipe covered by this specification is intended for buried gas distribution and gas transmission pressure piping applications. 1.2?This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specification F3373). Fittings to be used with PEX pipe manufactured to this specification are in Specification F2829/F2829M. Installation considerations are in X3.2. Note 1:?Inch-sized fittings should not be used for
metric-sized pipe, and metric-sized fittings should not be used for
inch-sized pipe.
1.3?The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 23.12.2024 (Počet položek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.