Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications (Includes all amendments And changes 4/15/2020).
Automaticky přeložený název:
Standardní specifikace pro Black síťovaného polyetylenu (PEX) trubky, armatury a klouby pro plynové distribuční aplikace
NORMA vydána dne 1.11.2014
Označení normy: ASTM F2968/F2968M-14a
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2014
Kód zboží: NS-54796
Počet stran: 9
Přibližná hmotnost: 27 g (0.06 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Trubky z plastické hmoty
Potrubí a potrubní spojky
Systémy dodávky plynu v budovách
Keywords:
crosslinked polyethylene, gas distribution, HDB, hydrostatic stress, metric, PEX, pipe, PPI, pressure,, ICS Number Code 23.040.20 (Plastic pipes), 23.100.40 (Piping and coupling), 91.140.40 (Gas supply systems)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers outside diameter controlled, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints, made in pipe dimension ratios ranging from 6 to 17, and pressure rated for gas distribution. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and squeeze-off. Requirements for pipe and fittings markings are also given. The pipe, fittings and joints covered by this specification are intended for buried gas distribution and gas transmission pressure piping applications. 1.2 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Note 1: Metric sized (SI units) pipe should only be joined
with corresponding metric sized fittings, and inch sized pipe
should only be joined with corresponding inch sized fittings. Inch
sized fittings should not be used for metric sized pipe, and metric
sized fittings should not be used for inch sized pipe.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
Historická
1.12.2013
Historická
1.11.2013
Historická
15.12.2014
Historická
1.3.2012
Historická
1.2.2013
Historická
1.3.2014
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.09.2024 (Počet položek: 2 346 114)
© Copyright 2024 NORMSERVIS s.r.o.