Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2769-18
Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems
Přeložit název
NORMA vydána dne 1.8.2018
Informace o normě:
Označení normy: ASTM F2769-18
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2018
Kód zboží: NS-856851
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Potrubí a součásti potrubí obecně
Systémy dodávky vody v budovách
Anotace textu normy ASTM F2769-18 :
Keywords:
hot water, hydrostatic stress, PE-RT, pipe, plastic pipe, polyethylene of raised temperature, PPI, pressure, potable water, PERT, tubing,, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines),91.140.60 (Water supply systems)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) plastic hot- and cold-water tubing and distribution systems components made in one standard dimension ratio and intended for 100 psig (6.9 bar) water service up to and including a maximum working temperature of 180 °F (82 °C). Components are comprised of tubing, fittings, valves and manifolds. Tubing may incorporate an optional polymeric inner, middle or outer layer. Testing of fittings and PE-RT tubing to the requirements of this standard indicate that these fittings are appropriate for use with PE-RT piping systems. Requirements and test methods are included for materials, workmanship, dimensions and tolerances, burst pressure, sustained pressure, oxidative resistance, temperature cycling tests, bend strength and environmental stress cracking. Also included are tests related to system malfunctions. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems. 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. Note 1: Suggested hydrostatic design stresses and hydrostatic
pressure ratings for tubing and fittings are listed in Appendix X1. UV labeling guidelines are
provided in Appendix X2.
Design, assembly, and installation considerations are provided in
Appendix X3. An optional
performance qualification and an in-plant quality control program
are recommended in Appendix
X4.
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
