Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F2623-08

Standard Specification for Polyethylene of Raised Temperature (PE-RT) SDR 9 Tubing

Automaticky přeložený název:

Standardní specifikace pro polyethylenu zvýšené teplotě ( PE - RT ) SDR 9 trubky

NORMA vydána dne 1.3.2008

Jazyk
Provedení	PDF - okamžité stažení - 1 932.20 Kč Tištěné - 1 932.20 Kč
Dostupnost	SKLADEM
Cena	1 932.20 Kč bez DPH
1 932.20 Kč

Informace o normě:

Označení normy: ASTM F2623-08
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2008
Kód zboží: NS-54265
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM F2623-08 :

Keywords:

hydronic heating, hydrostatic stress, irrigation, PE-RT, pipe, plastic pipe, polyethylene of raised temperature, PPI, pressure, radiant heating, tubing, Polyethylene (PE), Tubing, ICS Number Code 23.040.20 (Plastic pipes)

Doplňující informace

1. Scope

1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) SDR 9 tubing that is outside diameter controlled, and pressure rated for water at 73°F (23°C), 140°F (60°C) and 180°F (82.2°C). Included are requirements for material, workmanship, dimensions and tolerances, product tests, and markings for PE-RT tubing.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 The tubing produced under this specification shall be permitted for use in general fluid transport, including hydronics and irrigations systems.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D618-21	Standard Practice for Conditioning Plastics for Testing
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D3895-19	Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
PPI TR-4	PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.
MIL-STD-129	Marking for Shipment and Storage
FED-STD-123	Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
B36.10	Standards Dimensions of Steel Pipe (NTS) Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
F412-23	Standard Terminology Relating to Plastic Piping Systems
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials

Doporučujeme:

EviNor - Řízení a aktualizace českých norem

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.