Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2510/F2510M-17
Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes
Přeložit název
NORMA vydána dne 1.12.2017
Informace o normě:
Označení normy: ASTM F2510/F2510M-17
Poznámka: NEPLATNÁ
Datum vydání normy: 1.12.2017
Kód zboží: NS-807485
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2510/F2510M-17 :
Keywords:
corrugated HDPE pipe, corrugated PP pipe, design test method, hydrostatic testing, leakage tests, manholes, resilient connectors, seals,, ICS Number Code 93.030 (External sewerage systems)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||
|
1.1 This specification covers the design, material, and minimum performance requirements of resilient connectors used for connections between reinforced concrete structures conforming to Specifications C478 and C913 to annular corrugated profile wall high density polyethylene (HDPE) drainage and sewer pipe conforming to AASHTO M252, M294, and M330 or Specifications F2306/F2306M, F2648/F2648M, F2736, F2763, F2764/F2764M, and F2947/F2947M. 1.1.1 These connectors are designed to provide a positive seal between the pipe and manholes or other structures subjected to internal and external hydrostatic pressures less than 10.8 psi [74 KPa]. 1.1.2 Testing under this standard is limited to hydrostatic pressures. Alternate air and vacuum pressure testing involve unique testing protocols and are not addressed under this standard. 1.1.3 Testing under this standard is conducted in a laboratory as a proof of design certification. Actual field performance testing would be accomplished and accepted under individual project performance standards or pipeline acceptance criteria, which is outside the scope of this standard. Note 1: Infiltration or exfiltration quantities for an
installed system are dependent upon many factors other than the
connections between manhole structures and pipe, and allowable
quantities must be covered by other specifications and suitable
testing of the installed pipeline and system.
Note 2: This specification may be applied to other types of
plastic drainage pipe. Consult with manufacturer of pipe for
applicability to this standard.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 7. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
