Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2332-06(2013)
Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
Automaticky přeložený název:
Standardní specifikace pro Prstencové kuličkovými ložisky pro nástroje a přesných rotačních komponenty
NORMA vydána dne 1.5.2013
Informace o normě:
Označení normy: ASTM F2332-06(2013)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2013
Kód zboží: NS-53586
Počet stran: 145
Přibližná hmotnost: 466 g (1.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2332-06(2013) :
Keywords:
ABEC 5P, ABEC 7P, angular contact, barrier coating, bearing void, calibration (classification), contact angle, counterbored outer ring, deep groove radial, extended inner ring, instrument bearing, nonseparable, passivation, precision bearing, separable, starting torque, stepped inner ring, ICS Number Code 21.100.10 (Plain bearings)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P. 1.2 Intended Use—Ball bearings defined by this specification are intended for use in critical components of instrument systems. Such components range from air circulating blowers and drive motors through precision gear trains, gyro gimbals, and pickoffs to rate integrating spin-motors. 1.3 The specification contains many of the requirements of MIL-B-81793, which was originally developed by the Department of Defense and maintained by the Naval Air Systems Command (Navy-AS) in Lakehurst, NJ. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2
1.4 Classification—Annular ball bearings for instrument and precision rotating components shall be of the following types, as specified: 1.4.1 Type I—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged; (See 1.4.2 Type II—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged; (See 1.4.3 Type III—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged, inner ring extended; (See Annex A9 – Annex A12) 1.4.4 Type IV—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged, inner ring extended; (See Annex A13 – Annex A16) 1.4.5 Type V—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and counterbored outer ring; (See 1.4.6 Type VI—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, nonseparable, and counterbored outer ring on flange side; (See 1.4.7 Type VII—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, separable, and stepped inner ring; (See 1.4.8 Type VIII—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, separable, and stepped inner ring; (See 1.4.9 Type IX—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and stepped inner ring. (See 1.5 Inch-Pound Specification—This specification covers only the inch-pound bearings. 1.5.1 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
