Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F2034-18

Standard Specification for Sheet Linoleum Floor Covering

Přeložit název

NORMA vydána dne 1.9.2018

Jazyk
Provedení	PDF - okamžité stažení - 1 291.50 Kč PDF + redline - ihned - 1 549.70 Kč Tištěné - 1 291.50 Kč Tisk + redline - 1 549.70 Kč
Dostupnost	SKLADEM
Cena	1 291.50 Kč bez DPH
1 291.50 Kč

Informace o normě:

Označení normy: ASTM F2034-18
Datum vydání normy: 1.9.2018
Kód zboží: NS-900416
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Stropy. Podlahy. Schody

Anotace textu normy ASTM F2034-18 :

This specification covers sheet linoleum floor covering. These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. The floor coverings shall be of the following types: Type I; Type II; and Type III. The jute backing shall be firmly bonded to and partially embedded in the linoleum mix. The minimum amount of linoleum cement shall be 30 % when tested. The following test methods shall be performed: overall thickness; static load; resistance to chemicals; resistance to heat; resistance to light; flexibility; static dissipation; and wear surface.

Keywords:
drying room film, jute, linoleum, linoleum cement, rosin, sheet flooring, static dissipative,, ICS Number Code 91.060.30 (Ceilings. Floors. Stairs)

Doplňující informace

1. Scope

1.1 This specification covers sheet linoleum floor covering.

1.2 Three types of linoleum floor covering are covered (see Section 4). These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

F386-17(2022)	Standard Test Method for Thickness of Resilient Flooring Materials Having Flat Surfaces
F410-08(2022)	Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement
F710-22	Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring
F925-13(2020)	Standard Test Method for Resistance to Chemicals of Resilient Flooring
F970-22	Standard Test Method for Measuring Recovery Properties of Floor Coverings after Static Loading
F1482-21	Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring
F1514-19	Standard Test Method for Measuring Heat Stability of Resilient Flooring by Color Change
F1515-21	Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change
F150-06(2018)	Standard Test Method for Electrical Resistance of Conductive and Static Dissipative Resilient Flooring
F141-23	Standard Terminology Relating to Resilient Floor Coverings
F137-08(2018)	Standard Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus
ANSI/ASQC Z1.4	Sampling Procedures and Tables for Inspection by Attributes Available from American National Standards Institute, 11 West 42 nd St., 13th Floor, New York, NY 10036.
EN 670	Identification and Composition of Linoleum--Determination of Cement and Ash Residue Available from CEN European Committee for Standardization--Central Secretariat: rue de Stassart, 36 B-1050, Brussels.
F1516-23	Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)

Odebírejte informace o nově vydaných normách ZDARMA:

Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.