Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F1970-12
Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems
Automaticky přeložený název:
Standardní specifikace pro speciální Engineered Kování , příslušenstvím nebo ventily pro použití v poly (vinyl chloridu ) ( PVC) nebo chlorované poly (vinyl chloridu ) ( CPVC ) Systémy
NORMA vydána dne 1.11.2012
Informace o normě:
Označení normy: ASTM F1970-12
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2012
Kód zboží: NS-52283
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM F1970-12 :
Keywords:
appurtenances, check valves, CPVC, elastomeric joints, elastomers, fittings, flanges, PVC, SE, special-engineered, unions, valves, ICS Number Code 83.140.30 (Plastic pipes and fittings for non-fluid use)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers fittings, appurtenances and valves which are to be used with pipe and tubing complying with Specifications D1785, D2241, D2846/D2846M, F441/F441M or F442/F442M, or other piping as specified by the fittings manufacturer. These products, such as unions, flanges or valves, are not included in the scope of existing ASTM specifications. This specification includes minimum requirements for testing, materials, dimensions, workmanship, marking, and in-plant quality control. 1.2 Fittings or appurtenances covered by this specification are generally either molded, fabricated, or assembled from molded or machined components. The materials used in components include rigid thermoplastics, thermoplastic elastomers, elastomerics, and metals. The body or main portion of the fitting, appurtenance or valve is typically PVC, CPVC, PE or PA (nylon). All products covered by this standard are intended to be used in PVC or CPVC plastic piping systems, or as a transition from these to metal systems. 1.3 The application of these products to gas service is beyond the scope of this specification. 1.4 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. 1.5 Fittings which rely on heat
fusion welding for connection to the piping system are outside the
scope of this specification.
1.6 Check valves (including foot valves) covered by this specification shall not be considered backflow prevention devices and shall not be used for the protection of a potable water supply. For definitions and requirements of backflow prevention devices, consult model plumbing codes and ASSE.1.7 Due to the complex and installation-specific concerns surrounding chemical resistance and corrosion, this specification does not address the compatibility of the products with all possible end-use environments. Additional testing specific to the end-use environment is recommended if the system is conveying liquids other than potable water. 1.8 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are given for information only. 1.9 The following safety
caveat applies only to the test methods and in-plant quality
control portions, section of this specification:
Standard Classification System and Basis
for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds
and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds Standard Specification for Poly(Vinyl
Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes
all amendments and changes 10/8/2021). Standard Test Method for Determining
Dimensions of Thermoplastic Pipe and Fittings Standard Specification for Poly(Vinyl
Chloride) (PVC) Pressure-Rated Pipe (SDR Series) Standard Test Method for Time-to-Failure
of Plastic Pipe Under Constant Internal Pressure Standard Specification for Elastomeric
Seals (Gaskets) for Joining Plastic Pipe Standard Test Method for Resistance to
Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and
Fittings Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) Standard Practice for Sampling of
Plastics (Withdrawn 1998) Standard Classification System for Rubber
Products in Automotive Applications Standard Specification for Poly(Vinyl
Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 Standard Specification for Poly(Vinyl
Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Chlorinated
Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water
Distribution Systems (Includes all amendments and changes
4/29/2019). Standard Terminology Relating to Plastic
Piping Systems Standard Specification for Socket-Type
Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings,
Schedule 40 Standard Specification for Chlorinated
Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 Standard Specification for Chlorinated
Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 Standard Specification for Chlorinated
Poly(Vinyl Chloride) (CPVC) Plastic Pipe (SDR–PR) Standard Specification for Taper Pipe
Threads 60° for Thermoplastic Pipe and Fittings B1.20.1 Pipe Threads, General Purpose (Inch)
Available from American Society of Mechanical Engineers (ASME),
ASME International Headquarters, Three Park Ave., New York, NY
10016-5990. B16.5 Pipe Flanges and Flanged Fittings NSF 14 Plastics Piping Components and Related
Materials NSF International, P.O. Box 130140, Ann Arbor, MI
48113-0140. NSF 61 Drinking Water System Components - Health
Effects ISA S75.02 Control Valve Capacity Test Procedure
Instrument Society of America, 67 Alexander Drive, Research
Triangle Park, NC 27709. ANSI/ASQ Z1.4 Sampling Procedures and Tables for
Inspection by Attributes American Society for Quality, 611 East
Wisconsin Ave., Milwaukee, WI 53201-3005. |
Doporučujeme:
