Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Performance of Pressure Fryers
Přeložit název
NORMA vydána dne 1.3.2021
Označení normy: ASTM F1964-21
Datum vydání normy: 1.3.2021
Kód zboží: NS-1029248
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
efficiency, energy, kettle fryer, performance, pressure fryer, production capacity, throughput,, ICS Number Code 91.040.20 (Buildings for commerce and industry)
Significance and Use | ||||||
5.1?The energy input rate test is used to confirm that the fryer under test is operating in accordance with its nameplate rating. 5.2?Fryer temperature calibration is used to ensure that the fryer being tested is operating at the specified temperature. Temperature calibration also can be used to evaluate and calibrate the thermostat control dial. 5.3?Preheat energy and time can be used by food service operators to manage their restaurants' energy demands, and to estimate the amount of time required for preheating a fryer. 5.4?Idle energy rate and pilot energy rate can be used to estimate energy consumption during noncooking periods. 5.5?Preheat energy, idle energy rate, pilot energy rate, and heavy-load cooking energy rates can be used to estimate the fryer's energy consumption in an actual food service operation. 5.6?Cooking energy efficiency is a direct measurement of fryer efficiency at different loading scenarios. This information can be used by food service operators in the selection of fryers, as well as for the management of a restaurants' energy demands. 5.7?Production capacity is used by food service operators to choose a fryer that matches their food output requirements. |
||||||
1. Scope | ||||||
1.1?This test method evaluates the energy consumption and cooking performance of pressure and kettle fryers. The food service operator can use this evaluation to select a fryer and understand its energy efficiency and production capacity. 1.2?This test method is applicable to floor model natural gas and electric pressure fryers. 1.3?The fryer can be evaluated with respect to the following: 1.3.1?Energy input rate (10.2), 1.3.2?Preheat energy and time (10.4), 1.3.3?Idle energy rate (10.5), 1.3.4?Pilot energy rate (10.6, if applicable), 1.3.5?Cooking energy rate and efficiency (10.9), and 1.3.6?Production capacity (10.9). 1.4?The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
2. Referenced Documents | ||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.12.2024 (Počet položek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.