Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
Přeložit název
NORMA vydána dne 1.8.2016
Označení normy: ASTM F1901-16
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2016
Kód zboží: NS-650507
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
DWV, pipe fittings, pipes, plastic pipes, polyethylene, recycle, waste disposal (building),, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers requirements for polyethylene (PE) pipe and fittings for nonpressure roof drain systems. 1.2 This specification covers pipe and fittings intended for normal residential and commercial uses and is not intended for use in unusual corrosive conditions. Note 1: Before installing pipe for waste disposal use, the
approval of the cognizant building code authority shall be obtained
as conditions not found in normal use or temperatures approaching
140°F (60°C) may be encountered.
1.3 Pipe is produced in dimensions based on outside diameters of 32 mm (1.250 in.) and larger in accordance with Specification F714. 1.4 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification. 1.5 Pipe and fittings are joined by the heat-fusion method, by the electrofusion method, or by using mechanical joints (excluding insert fittings) recommended by the manufacturer. 1.6 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are provided for information only. 1.7 The following safety hazards caveat pertains
only to the test method, Section 7, of this specification.
Standard Specification for Polyethylene
Plastics Pipe and Fittings Materials B36.10 Standard Dimensions of Steel Pipe
(IPS) Standard Practice for Heat Fusion Joining
of Polyethylene Pipe and Fittings (Includes all amendments and
changes 3/17/2022). Standard Specification for Taper Pipe
Threads 60° for Thermoplastic Pipe and Fittings Standard Specification for Polyethylene
Plastics Molding and Extrusion Materials (Includes all amendments
and changes 11/17/2022). Standard Guide for Development of ASTM
Standards Relating to Recycling and Use of Recycled Plastics
(Withdrawn 2007) Standard Terminology Relating to Plastic
Piping Systems Standard Specification for Elastomeric
Seals (Gaskets) for Joining Plastic Pipe Standard Test Method for Water Absorption
of Plastics Standard Practice for Conditioning
Plastics for Testing Standard Practice for Electrofusion
Joining Polyolefin Pipe and Fittings 3607 Polyethylene Pipe: Tolerances on Outside
Diameters and Wall Thicknesses 161 Thermoplastic Pipe for the Transport of
FluidsNominal Outside Diameters and Nominal Pressures MIL-STD-129 Marking for Shipment and Storage Fed. Std. No. 123 Marking for Shipment (Civil Agencies) Standard Specification for Drain, Waste,
and Vent (DWV) Plastic Fittings Patterns Standard Practice for Determination of
the Impact Resistance of Thermoplastic Pipe and Fittings by Means
of a Tup (Falling Weight) Standard Test Method for Determination of
External Loading Characteristics of Plastic Pipe by Parallel-Plate
Loading Standard Test Method for Determining
Dimensions of Thermoplastic Pipe and Fittings Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) Standard Specification for Polyethylene
(PE) Plastic Pipe (DR-PR) Based on Outside Diameter Standard Practices for Evaluating the
Resistance of Plastics to Chemical Reagents |
Poslední aktualizace: 26.04.2024 (Počet položek: 2 896 057)
© Copyright 2024 NORMSERVIS s.r.o.