Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Comparison of Rearfoot Motion Control Properties of Running Shoes
Automaticky přeložený název:
Standardní zkušební metoda pro porovnání Motion vlastností běžecké boty Control rearfoot
NORMA vydána dne 1.11.2011
Označení normy: ASTM F1833-97(2011)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2011
Kód zboží: NS-51750
Počet stran: 9
Přibližná hmotnost: 27 g (0.06 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
orthoses, pronation, rearfoot motion, running shoe, stability, Athletic footwear, Orthoses, Pronation, Rearfoot motion, Running shoes, Stability--consumer products, ICS Number Code 61.060 (Footwear)
Significance and Use | ||
This test method allows the rearfoot control properties of running shoes or corrective orthoses within shoes to be compared provided they are tested concurrently and under identical conditions. Tests of this type are commonly used in the development and performance testing of running shoes and other in-shoe devices. Careful adherence to the requirements and recommendations of this test shall provide results which can be compared between different laboratories. Note 1—The variance in rearfoot motion due to differences between shoes is generally smaller than the variance between subjects. Direct comparisons between shoes tested in different experiments is therefore not possible. |
||
1. Scope | ||
1.1 This test method covers the measurement of certain angular motions of the lower extremity during running, specifically, the frontal plane projection of the pronation and supination of the lower leg relative to the foot (“rearfoot motion”) and methods by which the effects of different running shoes on rearfoot motion may be compared. 1.2 As used in this test method, footwear may refer to running shoes, corrective shoe inserts (orthoses) or specific combinations of both. The effects of orthoses may vary from shoe to shoe. Therefore, comparisons involving orthoses shall be qualified by the specific style of shoes in which they are tested. 1.3 This test method is limited to the measurement of the two dimensional, frontal plane projection of the relative angular motion between the lower leg and the foot (“rearfoot motion”). It is not a direct measure of pronation or supination, which are three dimensional motions. 1.4 This test method is limited to running motions in which the heel makes first contact with the ground during each step. 1.5 This test method is applicable to measurements of rearfoot motion made while subjects run on a treadmill or while they run overground under controlled conditions. 1.6 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||
2. Referenced Documents | ||
|
Historická
15.1.2009
Historická
15.5.2012
Historická
1.5.2013
Historická
1.6.2014
Historická
1.11.2011
Historická
1.11.2011
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.