Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F1430/F1430M-14
Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments
Automaticky přeložený název:
Standardní zkušební metoda pro akustické emise testování izolovaných a neizolovaných Aerial Personální zařízení se napsat Manipulátory Přílohy
NORMA vydána dne 1.4.2014
Informace o normě:
Označení normy: ASTM F1430/F1430M-14
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2014
Kód zboží: NS-50267
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM F1430/F1430M-14 :
Keywords:
acoustic, aerial devices, emission, equipment, ICS Number Code 17.140.01 (Acoustic measurements and noise abatement in general)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||
|
5.1 This test method provides a means of evaluating acoustic emissions generated by the rapid release of energy from localized sources within an APD under controlled loading. The resultant energy releases occur during intentional application of a controlled predetermined load. These energy releases can be monitored and interpreted by qualified individuals. 5.2 This test method permits testing of the major components of an aerial device under controlled loading. This test method utilizes objective criteria for evaluation and may be discontinued at any time to investigate a particular area of concern or prevent a fault from continuing to ultimate failure. 5.3 This test method provides a means of detecting acoustic emissions that may be defects or irregularities, or both, affecting the structural integrity or intended use of the aerial device. 5.4 Sources of acoustic emission found with this test method shall be evaluated by either more refined acoustic emission test methods or other nondestructive techniques (visual, liquid penetrant, radiography, ultrasonics, magnetic particle, etc.). Other nondestructive tests may be required to locate defects present in APDs. 5.5 Defective areas found in aerial devices by this test method should be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this test method. |
||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||
|
1.1 This test method describes a procedure for acoustic emission (AE) testing of aerial personnel devices (APDs) with supplemental load handling attachments. 1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted aerial personnel devices with supplemental load handling attachments: 1.1.1.1 Extensible-boom APDs, 1.1.1.2 Articulating-boom APDs, and 1.1.1.3 Any combination of 1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment: 1.1.2.1 Aerial personnel devices without supplemental load handling attachments, 1.1.2.2 Digger-derricks with platform, 1.1.2.3 Cranes with platform, and 1.1.2.4 Aerial devices with load-lifting capabilities located anywhere other than adjacent to the platform. 1.2 The AE test method is used to
detect and area-locate emission sources. Verification of emission
sources may require the use of other nondestructive test (NDT)
methods, such as radiography, ultrasonics, magnetic particle,
liquid penetrant, and visual inspection. (Warning—This test method requires that
external loads be applied to the superstructure of the vehicle
under test. During the test, caution must be taken to safeguard
personnel and equipment against unexpected failure or instability
of the vehicle or components.)
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
