Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F1200-21a
Standard Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150?F (1 MPa and 65?C)) (Includes all amendments and changes 9/14/2021).
Přeložit název
NORMA vydána dne 1.9.2021
Informace o normě:
Označení normy: ASTM F1200-21a
Datum vydání normy: 1.9.2021
Kód zboží: NS-1034914
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F1200-21a :
This specification covers welded pipe line strainers for use in applications above 150 psig and 150 F as well as in marine environment conditions. Strainers covered in this specification are classified into simplex, duplex (or multiplex), and automatic (self-cleaning) based on general construction. However, other bases for further classifying strainers are available: pressure ratings and types of port connection, port alignments relative to unit center lines, cover closures, valve types (in duplex), types of baskets or elements, materials of construction, and other design features. Strainers shall be manufactured by casting or forging or fabricated from plates, tubes, or pipes, with inlet and outlet connections requiring welding joined by butt welding. On the other hand, strainers made of carbon or low alloy steel shall be post-weld heat treated. The strainers shall undergo either hydrostatic or air test, while the welds shall be examined visually or radiographically. All tests shall conform to the requirements specified.
Keywords:
cast strainers, marine strainer, strainer, welded strainers ,, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines)
Doplňující informace
| 1. Scope | ||||||
|
1.1?This specification covers welded strainers in services above 150 psig or 150?F (1 MPa and 65?C). For welded strainers in services at or below these ratings and cast strainers, see Specification F1199. 1.2?This specification provides the minimum requirements for the design fabrication, rating, marking, and testing of welded pipe line strainers for services above 150 psig or 150?F (1 MPa and 65?C). Note 1:?Fabricated (welded) pipe line strainers meeting this
standard may also be used at pressures of 150 psig (1 MPa) and
below and 0?F (18?C) and above.
1.3?Strainers manufactured to this specification are acceptable for use in the marine environment. 1.4?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5?The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
