Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Evaluating Absorptive Solar Receiver Materials When Exposed to Conditions Simulating Stagnation in Solar Collectors with Cover Plates
Přeložit název
NORMA vydána dne 1.5.2023
Označení normy: ASTM E781-86(2023)
Datum vydání normy: 1.5.2023
Kód zboží: NS-1142764
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
absorber, absorptance, aging, cover plates, emittance, outdoor weathering, selective absorber, solar collectors, stagnation, thermal testing, weathering,, ICS Number Code 27.160 (Solar energy engineering)
Significance and Use | ||||||||||||||
4.1?Although this practice is intended for evaluating solar absorber materials and coatings used in flat-plate collectors, no single procedure can duplicate the wide range of temperatures and environmental conditions to which these materials may be exposed during in-service conditions. 4.2?This practice is intended as a screening test for absorber materials and coatings. All conditions are chosen to be representative of those encountered in solar collectors with single cover plates and with no added means of limiting the temperature during stagnation conditions. 4.3?This practice uses exposure in a simulated collector with a single cover plate. Although collectors with additional cover plates will produce higher temperatures at stagnation, this procedure is considered to provide adequate thermal testing for most applications. Note 1:?Mathematical modeling has shown that a selective
absorber, single glazed flat-plate solar collector can attain
absorber plate stagnation temperatures as high as 226 ?C (437 ?F)
with an ambient temperature of 37.8 ?C (100 ?F) and zero wind
velocity, and a double glazed one as high as 245 ?C (482 ?F) under
these conditions. The same configuration solar collector with a
nonselective absorber can attain absorber stagnation temperatures
as high as 146 ?C (284 ?F) if single glazed, and 185 ?C (360 ?F) if
double glazed, with the same environmental conditions (see
Performance Criteria for Solar Heating and Cooling Systems in
Commercial Buildings, NBS Technical Note 1187).4
4.4?This practice evaluates the thermal stability of absorber materials. It does not evaluate the moisture stability of absorber materials used in actual solar collectors exposed outdoors. Moisture intrusion into solar collectors is a frequent occurrence in addition to condensation caused by diurnal breathing. 4.5?This practice differentiates between the testing of spectrally selective absorbers and nonselective absorbers. 4.5.1?Testing Spectrally Selective Absorber Coatings and MaterialsSpectrally selective solar absorptive coatings and materials require testing in a covered enclosure that contains a selectively coated sample mounting plate, such that the enclosure and mounting plate simulate the temperature conditions of a selective flat-plate collector exposed under stagnation conditions. 4.5.2?Testing Nonselective Coatings and MaterialsSpectrally nonselective solar absorptive coatings and materials require testing in a covered enclosure that contains a nonselective coated sample mounting plate, such that the enclosure and mounting plate simulate the temperature conditions of a covered, nonselective flat-plate collector exposed under stagnation conditions. |
||||||||||||||
1. Scope | ||||||||||||||
1.1?This practice covers a test procedure for evaluating absorptive solar receiver materials and coatings when exposed to sunlight under cover plate(s) for long durations. This practice is intended to evaluate the exposure resistance of absorber materials and coatings used in flat-plate collectors where maximum non-operational stagnation temperatures will be approximately 200 ?C (392 ?F). 1.2?This practice shall not apply to receiver materials used in solar collectors without covers (unglazed) or in evacuated collectors, that is, those that use a vacuum to suppress convective and conductive thermal losses. 1.3?The values stated in SI units are to be regarded as the standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.