Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM E519/E519M-22
Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages
Přeložit název
NORMA vydána dne 1.12.2022
Informace o normě:
Označení normy: ASTM E519/E519M-22
Datum vydání normy: 1.12.2022
Kód zboží: NS-1097770
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM E519/E519M-22 :
Keywords:
compressive strength, diagonal loading, diagonal tensile strength, diagonal tension, masonry assemblages, masonry units, mortar, shear, shear strength,, ICS Number Code 91.060.10 (Walls. Partitions. Facades)
Doplňující informace
| Significance and Use | ||||||||||||
|
3.1?This test method was developed to measure more accurately the diagonal tensile (shear) strength of masonry than was possible with other available methods. The specimen size was selected as being the smallest that would be reasonably representative of a full-size masonry assemblage and that would permit the use of testing machines such as are used by many laboratories. Note 1:?As a research test method used only for the purpose of
evaluating the effects of variables such as type of masonry unit,
mortar, workmanship, etc., a smaller size specimen could be used if
the available testing equipment will not accommodate a 1.2-m [4-ft]
square specimen. However, there is a lack of experimental data that
would permit an evaluation of the effect of specimen size on the
shear strength or to permit a correlation between the results of
small-scale specimen tests and larger specimens.
|
||||||||||||
| 1. Scope | ||||||||||||
|
1.1?This test method covers determination of the diagonal tensile or shear strength of masonry assemblages by loading them in compression along one diagonal (see Fig. 1), thus causing a diagonal tension failure with the specimen splitting apart parallel to the direction of load. FIG. 1 Apparatus for Determination of Diagonal Tensile or Shear Strength Masonry Assemblages 1.2?Annex A1 provides requirements regarding the determination of the diagonal-tension strength of masonry under combined diagonal-tension and compressive loading. 1.3?The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4?These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5?This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
