Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Measuring Deflections using a Portable Impulse Plate Load Test Device
Automaticky přeložený název:
Standardní zkušební metoda pro měření průhybů pomocí přenosného Impulse Plate Load testovací zařízení
NORMA vydána dne 1.6.2011
Označení normy: ASTM E2835-11
Poznámka: NEPLATNÁ
Datum vydání normy: 1.6.2011
Kód zboží: NS-46108
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
deflection surveys, deflection test methods, deflection testing, Dynamic Plate Load Testing (DPLT), Light Drop Weight Tester (LDWT),, impulse deflection testing device, Light Weight Deflectometer (LWD), load-deflection testing, Nondestructive Testing (NDT), pavement deflection, pavement foundation layers, pavement layer modulus, pavement layer stiffness, Portable Falling Weight Deflectometer (PFWD), Portable Impulse Plate Load Test, quality assurance
Significance and Use | ||||
This test method covers the determination of plate deflection resulting from the application of an impulse load. The deflection is measured at the center of the top of the load plate (see Note 1). Note 1—If the load plate is in “perfectly uniform” contact with the unbound material under the plate, then deflection of the load plate should be equal to the deflection of the surface of the unbound material under test. However, with typical unbound materials a 100% uniform contact can seldom be achieved. Accordingly, the test surface shall be as clean and smooth as possible with loose granules and protruding material removed. For gravel surfaces it is recommended that a thin layer of fine sand be placed over the test point. For fine-grained materials, this will help in obtaining a reasonably uniform contact between the load plate and the surface. See 5.1 in Test Method . Deflections may be either correlated directly to pavement performance or used to determine in-situ material characteristics of the pavement foundation layers. Some uses of the data include quality control and quality assurance of compacted layers, and for structural evaluation of load carrying capacity (see Note 2 and Guide ). Note 2—The volume of the pavement foundation materials affected by the applied load is a function of the magnitude of the load, plate size and rigidity, loading rate, buffer stiffness, and the stiffness and shear strength of the pavement foundation materials. Therefore, care must be taken when analyzing the results because the data obtained by the Portable Impulse Plate Load Test may be obtained under substantially different conditions than when a heavy moving wheel load passes over the pavement surface after construction is complete. |
||||
1. Scope | ||||
1.1 This test method applies to measuring plate deflections using a Portable Impulse Plate Load Test device. The method covers the measurement of deflection of the load plate rather than the deflection of the surface of the pavement or foundation layers (see Note 1). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||
2. Referenced Documents | ||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.