Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM E2583-07(2015)
Standard Test Method for Measuring Deflections with a Light Weight Deflectometer (LWD)
Automaticky přeložený název:
Standardní testovací metoda měření průhybů s nízkou hmotností Deflectometer (LWD)
NORMA vydána dne 1.9.2015
Informace o normě:
Označení normy: ASTM E2583-07(2015)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2015
Kód zboží: NS-622663
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM E2583-07(2015) :
Keywords:
deflection surveys, deflection testing, Falling Weight Deflectometer (FWD), Light Weight Deflectometer (LWD), impulse deflection testing, load-deflection testing, Nondestructive testing (NDT), pavement deflection, pavement testing, pavement layer modulus, pavement layer stiffness, Portable Falling-Weight Deflectometer (PFWD),, ICS Number Code 93.080.10 (Road construction)
Doplňující informace
| Significance and Use | ||||||
|
4.1 This test method covers the determination of surface deflections as a result of the application of an impulse load. The resulting deflections are measured at the center of the applied load and may also be measured at various distances away from the load. Deflections may be either correlated directly to pavement performance or used to determine in-situ material characteristics of the pavement layers. Some uses of data include quality control and quality assurance of compacted layers, structural evaluation of load carrying capacity, and determination of thickness requirements for highway and airfield pavements (see Guide D4695). Note 1: Since pavement and subgrade materials may be stress
dependent, care must be taken when analyzing LWD test data on
unbound materials so that the applied stress will closely match the
stress value applied by the design wheel load at the pavement
surface.
Note 2: The volume of the pavement and subgrade materials
affected by the load is a function of the magnitude of the load.
Therefore, care must be taken when analyzing the results, since the
data obtained by the LWD may be obtained from a smaller volume of
the unbound materials than under the influence of a heavy moving
wheel load at the pavement surface.
|
||||||
| 1. Scope | ||||||
|
1.1 This test method covers the determination of deflections of paved and unpaved surfaces with a Light Weight Deflectometer (LWD). This device is also referred to as a Portable Falling-Weight Deflectometer (PFWD). The LWD is lightweight, portable and generally used for testing unbound pavement layers. The deflections measured using an LWD can be used to determine the stiffness of bound and unbound pavement surfaces using appropriate back- or forwardcalculation analysis techniques. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
| 2. Referenced Documents | ||||||
|
Doporučujeme:
EviZak - všechny zákony včetně jejich evidence na jednom místě
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
