Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Ultrasonic Testing of Wrought Products
Přeložit název
NORMA vydána dne 1.12.2022
Označení normy: ASTM E2375-22
Datum vydání normy: 1.12.2022
Kód zboží: NS-1099430
Počet stran: 23
Přibližná hmotnost: 69 g (0.15 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
angle beam, contact method, immersion ultrasonic, longitudinal wave, nondestructive, straight beam, ultrasonic, ultrasonic examination, ultrasonic technique, ultrasound, wrought metal products, wrought metals,, ICS Number Code 71.040.99 (Other standards related to analytical chemistry)
Significance and Use | ||||||||||||||||||||||||||||||||||||||||
4.1?This practice is intended primarily for the examination of wrought metals, forged, rolled, machined parts or components to an ultrasonic class most typically specified in the purchase order or other contract document. |
||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||
1.1?PurposeThis practice establishes the minimum requirements for ultrasonic examination of wrought products. Note 1:?This practice was adopted to replace MIL-STD-2154, 30
Sept. 1982. This practice is intended to be used for the same
applications as the document which it replaced. Users should
carefully review its requirements when considering its use for new,
or different applications, or both.
1.2?ApplicationThis practice is applicable for examination of materials such as, wrought metals and wrought metal products having a thickness or cross section equal to 0.250 in. (6.35 mm) or greater. 1.2.1?Wrought Aluminum Alloy ProductsExamination shall be in accordance with Practice B594. Angle beam scans of wrought aluminum alloy products shall be performed in accordance with this practice as agreed upon by the purchaser and supplier. 1.3?Acceptance ClassWhen examination is performed in accordance with this practice, engineering drawings, specifications, or other applicable documents shall indicate the acceptance criteria. Five ultrasonic acceptance classes are defined in Table 1. One or more of these classes may be used to establish the acceptance criteria or additional or alternate criteria may be specified. 1.4?Order of PrecedenceContractual requirements and authorized direction from the cognizant engineering organization may add to or modify the requirements of this practice. Otherwise, in the event of conflict between the text of this practice and the references cited herein, the text of this practice takes precedence. Nothing in this practice, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1.5?Measurement ValuesThe values stated in inch-pounds are to be regarded as standard. The metric equivalents are in parentheses. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||
|
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 01.11.2024 (Počet položek: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.