Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Methods for Hydroxyl Groups Using Acetic Anhydride Acetylation
Automaticky přeložený název:
Standardní zkušební metody pro hydroxylové skupiny použití anhydridu kyseliny octové acetylačního
NORMA vydána dne 1.3.2010
Označení normy: ASTM E222-10
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2010
Kód zboží: NS-44701
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
acetic anhydride, acetylation, hydroxyl, hydroxyl groups, hydroxyl number, primary, secondary, volumetric, Acetic anhydride, Acetylation, Aliphatic hydrocarbons, Assay, Hydroxyl groups, Hydroxyl (hydroxide ion) content, Perchloric acid catalyzed method, Pressure bottle method, Reflux, Titration, Volumetric measurement, ICS Number Code 71.040.40 (Chemical analysis)
Significance and Use | ||||||||||||||||||
Hydroxyl is an important functional group, and knowledge of its content is required in many intermediate and end use applications. The test methods described herein are for the determination of primary and secondary hydroxyl groups and can be used for the assay of compounds containing them. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 These test methods cover the determination of hydroxyl groups attached to primary and secondary carbon atoms in aliphatic and alicyclic compounds and phenols. 1.2 Three test methods are given as
follows:
1.2.1 Test Method A is recommended for general use. Test Method B is included to give a standard procedure for the method that has been used widely. Test Method C is recommended when the results are required in a minimum period of time or where ambient temperature for the reaction is desired. 1.2.2 The results obtained using Test Methods A and B will be essentially the same, but the results obtained using Test Method C will be higher (up to approximately 4 % relative) than those obtained using the other two methods. 1.2.3 Statements on precision are included with each test method. The precision of Test Methods A and C is consistent over a wide range of hydroxyl content (tested over hydroxyl number range of 250 to 1600), whereas Test Method B is less precise at the higher hydroxyl content level than it is at the lower hydroxyl content level. In general, Test Method A is approximately two-fold as precise as Test Method C. Test Method B has approximately the same precision as Test Method C at the lower hydroxyl content level but poorer precision at the higher hydroxyl content level. 1.2.4 The interferences are essentially the same for the three methods. Some compounds can be analyzed using Test Methods A or B but not using Test Method C because of interfering reactions of the strong acid catalyst with the compound being analyzed or the acetate product formed in the determination. However, because of its increased reactivity, Test Method C is applicable for determination of some compounds, particularly sterically hindered secondary alcohols, which react too slowly or not at all in Test Methods A and B. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Review the current appropriate Material Safety Data Sheets (MSDS) for detailed information concerning toxicity, first aid procedures, and safety precautions. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7. Note 1—Other methods for determination of hydroxyl groups are given in Test Methods D1957, D2195, E326, E335, and . |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.10.2011
Historická
1.4.2013
Historická
1.10.2009
Historická
1.11.2011
Historická
1.8.2012
Historická
1.6.2013
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 03.11.2024 (Počet položek: 2 209 203)
© Copyright 2024 NORMSERVIS s.r.o.