Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Measuring the Frictional Properties of Winter Contaminated Pavement Surfaces Using an Averaging-Type Spot Measuring Decelerometer
Automaticky přeložený název:
Standardní zkušební metoda pro měření vlastností třecích zimní kontaminovaných Pavement povrchů Použití průměrování-Type Spot Měřicí Decelerometr
NORMA vydána dne 15.6.2014
Označení normy: ASTM E2101-14
Poznámka: NEPLATNÁ
Datum vydání normy: 15.6.2014
Kód zboží: NS-44295
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
airport runway friction, braking, deceleration, decelerometer, tire pavement friction, winter conditions, ICS Number Code 13.020.40 (Pollution, pollution control and conservation)
Significance and Use | ||
5.1 Knowledge of the frictional properties of a winter contaminated pavement surface is essential to evaluate the braking effort of ground vehicles or aircraft operating on a pavement surface. The presence of contaminants on a pavement surface will affect the frictional properties of the surface in a manner which is difficult to evaluate by visual observation alone. The frictional properties of a winter contaminated pavement surface can be characterized using a spot measuring decelerometer which provides a measurement of the surface friction and assists with the evaluation of pavement winter maintenance requirements. 5.2 The measurements produced by this test method should not be used as the sole criteria to determine pavement winter maintenance requirements. The measurements would normally be combined with visual and other observations to provide a more complete analysis of the pavement surface conditions. A certain amount of discretion is required on the part of the operator as this test method provides only a “spot” measurement of the surface condition. The objective of the operator is to identify areas of the winter contaminated pavement surface which may have lower friction and then obtain friction measurements in those areas. This makes the test method somewhat conservative by nature in comparison to the actual friction potential. 5.3 The measurements produced by this test method are dependent on the test vehicle parameters and on the braking technique of the vehicle operator. |
||
1. Scope | ||
1.1 This test method covers the measurement of the frictional properties of winter contaminated pavement surfaces using an averaging-type spot measuring decelerometer. The method produces a reading that is proportional to the deceleration sustained by a test vehicle fitted with pneumatic rubber tires braking with all wheels locked. A friction index for a section of winter contaminated pavement is determined from the average of several deceleration measurements recorded over the section of winter contaminated pavement. 1.2 This test method is applicable to averaging-type spot measuring decelerometers. 1.3 This test method is applicable to the following winter contaminated pavement surface conditions: 1.3.1 Ice; 1.3.2 Wet ice (ice covered with a thin film of moisture of a depth insufficient to cause hydroplaning); 1.3.3 Compacted snow, any depth; 1.3.4 Slush on ice, slush not exceeding 3 mm (0.1 in.) in depth; 1.3.5 Loose, dry snow, not exceeding 25 mm (1 in.) in depth; 1.3.6 Ice control chemical solution on ice; and 1.3.7 Sand on ice. 1.4 This test method shall not be used when the following winter contaminated pavement surface conditions are present: 1.4.1 Water on a bare pavement surface; 1.4.2 Slush; and 1.4.3 Loose snow exceeding 25 mm (1 in.) in depth. 1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are in inch-pound units and are not exact equivalents, therefore, each system must be used independent of the other, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||
2. Referenced Documents | ||
|
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 06.09.2024 (Počet položek: 2 346 102)
© Copyright 2024 NORMSERVIS s.r.o.