Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM E1925-18
Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
Přeložit název
NORMA vydána dne 1.10.2018
Informace o normě:
Označení normy: ASTM E1925-18
Datum vydání normy: 1.10.2018
Kód zboží: NS-904938
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM E1925-18 :
This specification covers engineering and design criteria for rigid wall relocatable structures (RWRSs) which shall be used for designing expandable and nonexpendable RWRSs. RWRSs shall be manufactured from recovered materials, wherein intimate contact of dissimilar materials shall not be allowed (to prevent galvanic corrosion), all components shall be adequately protected from corrosion, and the materials used shall not cause any skin irritation or injury to the person handling the material during transportation, operation, or maintenance of the equipment. Tests for compatibility, air transportability, ground mobility, rail transportability, forklift handling, erecting and striking, air tightness, blackout, humidity resistance, marine atmosphere, temperature, solar load, temperature shock, heat transfer, blowing sand, sunshine (ultraviolet effects), flame resistance, fungus resistance, squareness, panel flatness, roof loads, floor loads, door loads, panel attachment points, leveling devices, lifting and towing provision strength, tow and dragging simulator, flat and rotational drop (with or without skids), drop shock, impact resistance, electromagnetic interference provisions, water tightness, and lift shall be performed and shall conform to the requirements specified.
Keywords:
adhesive bonded, aluminum, bonding, expandable, honeycomb sandwich panels, non-expandable, foam and beam panels, relocatable buildings, relocatable structures, rigid wall shelters,, ICS Number Code 91.060.10 (Walls. Partitions. Facades)
Doplňující informace
| 1. Scope | ||||||
|
1.1 This specification covers engineering and design criteria required for the development of rigid wall relocatable structures (RWRS) and shall be applied to the design of expandable and nonexpandable RWRSs. This specification applies to present engineering and design requirements for effective RWRSs that are operable in a variety of environments without degradation and are capable of all specified transport modes. This specification shall be applied to the design of expandable and nonexpandable RWRSs. This specification is a conversion of a military standard that was approved by all departments and agencies of the Department of Defense. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains only to the test required portion, Section 10, of this specification. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
