Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM E1612/E1612M-94(2013)e1 1.9.2013 náhled

Doplňující informace

ASTM E1612/E1612M-94(2013)e1

Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures (Includes all amendments And changes 9/7/2017).

Automaticky přeložený název:

Standardní specifikace pro předem vytvořené architektury Kompresní Těsnění pro budovy a parkoviště staveb

NORMA vydána dne 1.9.2013

Jazyk
Provedení	PDF - okamžité stažení - 1 734.80 Kč Tištěné - 1 734.80 Kč
Dostupnost	SKLADEM
Cena	1 734.80 Kč bez DPH
1 734.80 Kč

Informace o normě:

Označení normy: ASTM E1612/E1612M-94(2013)e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2013
Kód zboží: NS-42361
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Pojiva. Těsnicí materiály

Anotace textu normy ASTM E1612/E1612M-94(2013)e1 :

Keywords:
architectural, buildings, compression seal, parking structures, seal, ICS Number Code 91.100.50 (Binders. Sealing materials)

Doplňující informace

Significance and Use

8.1 Architectural compression seals included in this specification shall be those as follows:

8.1.1 Without frames.

8.1.2 Without flanges and nosing material(s).

8.1.3 Used in interior or exterior applications.

8.1.4 Used in any construction of the building.

8.2 This specification will give users, producers, building officials, code authorities, and others a basis for verifying material and performance characteristics of representative specimens under common test conditions. This specification will produce data on the following:

8.2.1 The physical properties of the fully cured elastomeric alloy.

8.2.2 The movement capability in relation to the nominal joint width as defined under Test Method E1399/E1399M.

8.3 This specification compares similar architectural compression seals but is not intended to reflect the system's application. “Similar” refers to the same type of architectural compression seal within the same subsection under 8.4 This specification does not provide information on the following:

8.4.1 Durability of the architectural compression seal under actual service conditions, including the effects of cycled temperature on the compression seal.

8.4.2 Loading capability of the system and the effects of a load on the functional parameters established by this specification.

8.4.3 Shear and rotational movements of the specimen.

8.4.4 Any other attributes of the specimen, such as fire resistance, wear resistance, chemical resistance, air infiltration, watertightness, and so forth.

8.4.5 Testing or compatibility of substrates.

8.4.6 Strip seals.

8.4.7 Architectural compression seals used with frames.

8.4.8 Architectural compression seals used with flanges and nosing material(s).

8.5 This specification is intended to be used only as one element in the selection of an architectural compression seal for a particular application. It is not intended as an independent pass or fail acceptance procedure. Other standards shall be used in conjunction with this specification to evaluate the importance of other service conditions such as durability, structural loading, and compatibility.

1. Scope

1.1 This specification covers the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures. The preformed architectural compression seal is a rectangular elastomeric extrusion, having an internal baffle system produced continuously and longitudinally throughout the material. The architectural compression seal functions under compression and is usually chemically bonded in place with an adhesive.

1.2 This specification covers all colors of architectural compression seals.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D395-18	Standard Test Methods for Rubber Property´Compression Set
E1399/E1399M-97(2022)	Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
D471-16a(2021)	Standard Test Method for Rubber Property—Effect of Liquids (Includes all amendments and changes 6/25/2021).
D518-99	Standard Test Method for Rubber Deterioration-Surface Cracking (Withdrawn 2008)
D624-00(2020)	Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D746-20	Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D865-11(2018)	Standard Test Method for Rubber´Deterioration by Heating in Air (Test Tube Enclosure)
D1052-09(2019)	Standard Test Method for Measuring Rubber Deterioration´Cut Growth Using Ross Flexing Apparatus
D1149-18	Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment
D2000-18	Standard Classification System for Rubber Products in Automotive Applications
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D3183-10(2019)	Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
E577-85(1999)	Standard Guide for Dimensional Coordination of Rectilinear Building Parts and Systems
E631-15	Standard Terminology of Building Constructions
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension