Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM E154-99

Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover

Automaticky přeložený název:

Standardní zkušební metody pro vodní páry zpomalovače použít ve styku se Zemí Pod betonové desky, na stěnách , nebo jako půdopokryvná

NORMA vydána dne 10.2.1999

Jazyk
Provedení	Online zabezpečené PDF - 1 817.10 Kč Tištěné - 1 817.10 Kč
Dostupnost	SKLADEM
Cena	1817.10 Kč bez DPH
1 817.10 Kč

Informace o normě:

Označení normy: ASTM E154-99
Poznámka: NEPLATNÁ
Datum vydání normy: 10.2.1999
Kód zboží: NS-42115
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM E154-99 :

Keywords:

Admixtures-soil, Building constructions/materials-crawl spaces, Building constructions/materials-vapor barriers, Concrete slabs, Crawl spaces, Deterioration, Ground covers, Incubation room, Microbiological examination, Microbiological examination-paints/related coatings, Mixed pigments, Potting soil, Resistance-decay, Resistance-puncture, Resistance-vapor barrier materials in buildings, Resistance-water vapor, Soil, Soil burial test, Temperature tests-building materials

Doplňující informace

1. Scope

1.1 These test methods cover the determination of the properties of flexible membranes to be used as vapor retarders in contact with earth under concrete slabs, against walls, or as ground cover in crawl spaces. The test methods are applicable primarily to plastic films, and other flexible sheets. The materials are not intended to be subjected to sustained hydrostatic pressure. The procedures simulate conditions to which vapor retarders may be subjected prior to and during installation, and in service.

1.2 The test methods included are:

Section Water-Vapor Transmission of Material as Received 7 Water-Vapor Transmission after Wetting and Drying and after Long-Time Soaking 8 Tensile Strength 9 Resistance to Puncture 10 Resistance to Plastic Flow and Elevated Temperature 11 Effect of Low Temperatures on Flexibility 12 Resistance to Deterioration from Organisms and Substances in Contacting Soil 13 Resistance to Deterioration from Petroleum Vehicles for Soil Poisons 14 Resistance to Deterioration from Exposure to Ultraviolet Light 15 Resistance to Flame Spread 16 Report 17

1.3 The values stated in acceptable metric units shall be considered standard. The values in parentheses are for information only.

1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C755-20	Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation
D1985-13(2019)	Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks
F1249-20	Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
E631-15	Standard Terminology of Building Constructions
E437-92(1997)	Specification for Industrial Wire Cloth and Screens (Square Opening Series) (Withdrawn 2000)
E241-20	Standard Guide for Limiting Water-Induced Damage to Buildings
E96/E96M-23	Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
E84-23d	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
D4397-16(2023)	Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications
D2565-23	Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
D1709-22	Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
D882-18	Standard Test Method for Tensile Properties of Thin Plastic Sheeting
D828-22	Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus
C168-22	Standard Terminology Relating to Thermal Insulation

Odebírejte informace o nově vydaných normách ZDARMA:

Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.