Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Acceptance of Evidence Based on the Results of Probability Sampling
Přeložit název
NORMA vydána dne 1.4.2018
Označení normy: ASTM E141-10(2018)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2018
Kód zboží: NS-847267
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
audit subsample, confidence limits, estimate, equal complete coverage, finite population correction, hypergeometric distribution, interpenetrating subsamples, population parameter, probability sampling, replicate subsamples, sample size, sampling distribution, sampling frame, sampling unit, skewness, standard error,, ICS Number Code 03.120.30 (Application of statistical methods)
Significance and Use | ||||||||||
4.1 This practice is designed to permit users of sample survey data to judge the trustworthiness of results from such surveys. Practice E105 provides a statement of principles for guidance of ASTM technical committees and others in the preparation of a sampling plan for a specific material. Guide E1402 describes the principal types of sampling designs. Practice E122 aids in deciding on the required sample size. 4.2 Section 5 gives extended definitions of the concepts basic to survey sampling and the user should verify that such concepts were indeed used and understood by those who conducted the survey. What was the frame? How large (exactly) was the quantity 4.3 If the sample design was relatively simple, such as simple random or stratified, then fully valid estimates of sampling variance are easily available. If a more complex design was used then methods such as discussed in Ref 4.4 Once the survey procedures that were used satisfy Section 5, see if any increase in sample size is needed. The calculations for making it objectively are described in Section 6. 4.5 Refer to Section 7 to guide in the interpretation of the uncertainty in the reported value of the parameter estimate, θ^, that is, the value of its standard error, se(θ^). The quantity 4.6 When the audit subsample shows that there was reasonable conformity with prescribed procedures and when the known instances of departures from the survey plan can be shown to have no appreciable effect on the estimate, the value of θ^ is appropriate for use. |
||||||||||
1. Scope | ||||||||||
1.1 This practice presents rules for accepting or rejecting evidence based on a sample. Statistical evidence for this practice is in the form of an estimate of a proportion, an average, a total, or other numerical characteristic of a finite population or lot. It is an estimate of the result which would have been obtained by investigating the entire lot or population under the same rules and with the same care as was used for the sample. 1.2 One purpose of this practice is to describe straightforward sample selection and data calculation procedures so that courts, commissions, etc. will be able to verify whether such procedures have been applied. The methods may not give least uncertainty at least cost, they should however furnish a reasonable estimate with calculable uncertainty. 1.3 This practice is primarily intended for one-of-a-kind studies. Repetitive surveys allow estimates of sampling uncertainties to be pooled; the emphasis of this practice is on estimation of sampling uncertainty from the sample itself. The parameter of interest for this practice is effectively a constant. Thus, the principal inference is a simple point estimate to be used as if it were the unknown constant, rather than, for example, a forecast or prediction interval or distribution devised to match a random quantity of interest. 1.4 A system of units is not specified in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
2. Referenced Documents | ||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 26.08.2024 (Počet položek: 2 344 895)
© Copyright 2024 NORMSERVIS s.r.o.