Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM E1032-19

Standard Practice for Radiographic Examination of Weldments Using Industrial X-Ray Film

Přeložit název

NORMA vydána dne 1.2.2019

Jazyk
Provedení	PDF - okamžité stažení - 1 671.00 Kč PDF + redline - ihned - 2 005.30 Kč Tištěné - 1 671.00 Kč Tisk + redline - 2 005.30 Kč
Dostupnost	SKLADEM
Cena	1671.00 Kč bez DPH
1 671.00 Kč

Informace o normě:

Označení normy: ASTM E1032-19
Datum vydání normy: 1.2.2019
Kód zboží: NS-938660
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Svarové spoje

Anotace textu normy ASTM E1032-19 :

This test method provides a uniform procedure for radiographic examination of weldments using industrial radiographic film. Requirements expressed in this method are intended to control the quality of the radiographic images and are not intended for controlling acceptability or quality of welds. The apparatus shall comprise of a radiation source which may be X-ray or gamma-ray source; film holders and cassettes; intensifying screens such as lead-foil, fluorescent, fluorometallic, or other metallic screens; filters which shall be used whenever the contrast reductions caused by low energy, scattered radiation, or the extent of undercut (edge burn-off) occurring on production radiographs are of significant magnitude to cause difficulty in meeting the quality level or radiographic coverage requirements stipulated by the job order or contract; masking to improve radiographic quality; IQI´s or penetrameters; shims, separate blocks, or like sections to facilitate IQI positioning; radiographic location and identification markers; and radiographic density measurement device. The test method shall meet the radiographic coverage, radiographic film quality, radiographic quality level, acceptance level, and radiographic density limitations. Procedures for surface preparation, radiation application and protection, IQI selection and placement, shim utilization, radiograph identification, and single-wall or double-wall radiographic techniques are addressed.

Keywords:

gamma ray, nondestructive testing, radiographic examination, radiography, weldments, X-ray ,, ICS Number Code 25.160.40 (Welding joints and welds)

Doplňující informace

1. Scope

1.1 This practice provides a uniform procedure for radiographic examination of weldments using industrial radiographic film. Requirements expressed in this practice are intended to control the quality of the radiographic images and are not intended for controlling acceptability or quality of welds.

1.2 The radiographic extent, the quality level, and the acceptance criteria to be applied shall be specified in the contract, purchase order, product specification, or drawings.

1.3 The radiographic techniques stated herein provide adequate assurance for defect detectability; however, it is recognized that, for special applications, specific techniques using more or less stringent requirements may be required than those specified. In these cases, the use of alternative radiographic techniques shall be as agreed upon between purchaser and supplier (also see Section 4).

1.4 The values stated in inch-pound units are to be regarded as standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E1254-13(2023)	Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
E1316-24	Standard Terminology for Nondestructive Examinations
E1815-18(2023)	Standard Test Method for Classification of Film Systems for Industrial Radiography
ANSI/ASNT-CP-189	Standard for Qualification and Certification of Nondestructive Testing Personnel
ISO5579	Nondestructive TestingRadiographic Examination of Metallic Materials by X and Gamma RaysBasic Rules
E390-20	Standard Reference Radiographs for Steel Fusion Welds
E543-21	Standard Specification for Agencies Performing Nondestructive Testing
E747-18	Standard Practice for Design, Manufacture and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology
E999-20	Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
E1025-18	Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiography
E1079-21	Standard Practice for Calibration of Transmission Densitometers
E94-04	Standard Guide for Radiographic Examination
E242-15(2020)	Standard Reference Radiographs for Appearances of Radiographic Images as Certain Parameters are Changed

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.