Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Measuring Chemical Emissions from Spray Polyurethane Foam (SPF) Insulation Samples in a Large-scale Ventilated Enclosure (Includes all amendments and changes 9/13/2022).Přeložit název
NORMA vydána dne 1.9.2022
Označení normy: ASTM D8445-22a
Datum vydání normy: 1.9.2022
Kód zboží: NS-1083927
Počet stran: 14
Přibližná hmotnost: 42 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
closed cell SPF, emissions, environmental concentration, full-scale ventilated enclosure, high-pressure application, indoor air quality, low-pressure application, open cell SPF, reentry times, reoccupancy times, spray polyurethane foam,
|Significance and Use
5.1?The demand for SPF insulation in homes and commercial buildings has increased as emphasis on energy efficiency increases. In an effort to protect the health and safety of both trade workers and building occupants due to the application of SPF, it is essential that reentry/reoccupancy-times into the structure where SPF has been applied, be established.
5.2?Concentrations of chemical emissions determined in large-scale ventilated enclosure studies conducted by this practice may be used to generate source emission terms for IAQ models.
5.3?The emission factors determined using this practice may be used to evaluate comparability and scalability of emission factors determined in other environments.
5.4?This practice was designed to determine emission factors for chemicals emitted by SPF insulation in a controlled room environment.
5.5?New or existing formulations may be sprayed, and emissions may be evaluated by this practice. The user of this practice is responsible for ensuring analytical methods are appropriate for novel compounds present in new formulations (see for target compounds and generic formulations).
5.6?This practice may be useful for testing variations in emissions from non-ideal applications. Examples of non-ideal applications include those that are off-ratio, applied outside of recommended range of temperature and relative humidity, or applied outside of manufacturer recommendations for thickness.
5.7?The determined emission factors are not directly applicable to all potential real-world applications of SPF. While this data can be used for VOCs to estimate indoor environmental concentrations beyond three days, the uncertainty in the predicted concentrations increases with increasing time. Estimating longer term chemical concentrations (beyond three days) for SVOCs is not recommended unless additional data (beyond this practice) is used, see 5.8?During the application of SPF, chemicals deposited on the non-applied surfaces (for example, floors and ceilings) are the result of both gaseous phase emissions from the SPF and overspray. It is difficult to separate these two processes with current analytical methods. At present, the difference in how these two processes impact the long-term emissions is not known. This practice combines these two processes to generate data for modeling inputs.
1.1?This practice describes procedures for measuring the chemical emissions of volatile and semi-volatile organic compounds (VOCs and SVOCs) from spray polyurethane foam (SPF) insulation samples in a large-scale ventilated enclosure.
1.2?This practice is used to identify emission rates and factors during SPF application and up to three days following application.
1.3?This practice can be used to generate emissions data for research activities or modeled for the purpose to inform potential reentry and reoccupancy times. Potential reentry and re-occupancy times only apply to the applications that meet manufacturer guidelines and are specific to the tested formulation.
1.4?This practice describes emission testing at ambient room and substrate temperature and relative humidity conditions recognizing chemical emissions may differ at different room and substrate temperatures and relative humidity.
1.5?This practice does not address all SPF chemical emissions. This practice addresses specific chemical compounds of potential health and regulatory concern including methylene diphenyl diisocyanate (MDI), polymeric MDI (MDI oligomeric polyisocyanates mixture), flame retardants, aldehydes, and VOCs including blowing agents, and catalysts. Although specific chemicals are discussed in this practice, other chemical compounds of interest can be quantified (see target compound and generic formulation list in ). Other chemical compounds used in SPF such as polyols, emulsifiers, and surfactants are not addressed by this practice. Particulate sizing and distribution are also outside the scope of this practice.
1.6?Emission rates during application are determined from air phase concentration measurements that may include particle bound chemicals. SVOC deposition to floors and ceilings is also quantified for post application modeling inputs. SVOC emission rates should only be used for modeling purposes for the duration of data collection.
1.7?Four quantification methods are described for isocyanates. The method chosen should consider safety issues such as flammability, the expected concentration, the presence of isocyanate aerosol during the phase of interest (during and post application), and if the tested SPF is high or low pressure.
1.8?This practice references similar standard practices for design, construction, performance evaluation, and use of full-scale chambers for chemical emission testing.
1.9?This practice references methods for the collection and analysis of air samples.
1.10?This practice applies to two-component open cell and closed cell SPF insulation system formulations that are processed using high-pressure or low-pressure installation processing practices and equipment.
1.11?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.12?This standard does not purport to address all of the safety concerns, if any, associated with its use. The application of SPF in a ventilated enclosure has the potential to generate a hazardous condition putting the individual responsible for spraying inserts at risk. It is the responsibility of the user of this standard to establish appropriate health and safety procedures and require appropriate certified personal protective equipment (PPE) to minimize chemical exposure. Individuals entering the ventilated enclosure during and after SPF application, for any amount of time, are expected to wear appropriate PPE.
1.13?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.14?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 29.02.2024 (Počet položek: 2 880 691)
© Copyright 2024 NORMSERVIS s.r.o.