Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determining the Aperture Stability Modulus of Geogrids
Přeložit název
NORMA vydána dne 1.6.2023
Označení normy: ASTM D7864/D7864M-15(2023)
Datum vydání normy: 1.6.2023
Kód zboží: NS-1145011
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
aperture stability modulus, geogrids, index test, laboratory test,, ICS Number Code 59.080.70 (Geotextiles)
Significance and Use | ||||||
5.1?The aperture stability modulus is a measure of the in-plane shear modulus, which is a function of other geogrid characteristics, most notably junction stability, flexural rib stiffness, and rib tensile modulus. 5.2?The test data can be used in conjunction with interpretive methods to evaluate the geogrid aperture stability at various traffic loads and base/subgrade conditions. Note 1:?Aperture stability modulus is referenced in the FHWA
Geosynthetics Design and Construction Guidelines (2008) as an input
parameter for the design of geogrid-reinforced unpaved roads using
punched and drawn biaxial geogrids. Geogrids of different
manufacturing process and material composition may use this
property in calibration and validation of their material within the
associated design.
5.3?This test method is not intended for routine acceptance testing of geogrid. This test method should be used to characterize geogrid intended for use in applications in which aperture stability is considered relevant. |
||||||
1. Scope | ||||||
1.1?This test method covers the procedure for measuring the Aperture Stability Modulus of a geogrid. (The terms Secant Aperture Stability Modulus, Torsional Rigidity Modulus, In-plane Shear Modulus, and Torsional Stiffness Modulus have been used in the literature to describe this same property.) 1.2?This test method is intended to determine the in-plane stability of a geogrid by clamping a center node and measuring the stiffness over an area of the geogrid. This test method is applicable for various types of geogrid. 1.3?This test method is intended to provide characteristic properties for design. The test method was developed for pavement and subgrade improvement calibrated design methods requiring input of aperture stability modulus. 1.4?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
2. Referenced Documents | ||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 13.09.2024 (Počet položek: 2 429 660)
© Copyright 2024 NORMSERVIS s.r.o.