Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter
Přeložit název
NORMA vydána dne 1.4.2022
Označení normy: ASTM D7619-22
Datum vydání normy: 1.4.2022
Kód zboží: NS-1058402
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
automatic particle counting, automotive diesel, biodiesel, fuel cleanliness, gas oil, gasoline, kerosine, marine diesel,, ICS Number Code 75.160.20 (Liquid fuels)
Significance and Use | ||||||||||||||||||||||||||||||||||||
5.1?This test method is intended for use in the laboratory or in the field for evaluating the cleanliness of distillate fuels, and liquid bio fuels. It is not applicable to on or in-line applications. 5.2?This test method offers advantage over traditional filtration methods in that it is a precise rapid test, and advantage over visual methods as it is not subjective. 5.3?An increase in particle counts can indicate a change in the fuel condition caused by storage or transfer for example. 5.4?High levels of particles can cause filter blockages and have a serious impact on the life of pumps, injectors, pistons and other moving parts. Knowledge of particle size in relation to the metallurgy can provide vital information especially if the hardness of particles is also known from other sources. 5.5?This test method specifies a minimum requirement for reporting measurements in particle size bands (see A1.1.2). Some specific applications may require measurements in other particle size bands. 5.6?Obtaining a representative sample and following the recommended sample and test specimen preparation procedures and timescales is particularly important with particle counting methods. (See Sections 8, 10, 14.1.4 and Note 8.) 5.7?This test method can also be used to estimate the total particulate counts excluding free water droplets in aviation turbine fuels by a chemical pretreatment of the fuel. See Appendix X2. |
||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||
1.1?This test method uses a specific automatic particle counter2 (APC) to count and measure the size of dispersed dirt particles, water droplets and other particles, in light and middle distillate fuel, and bio fuels such as biodiesel and biodiesel blends, in the overall range from 4 ?m(c) to 100 ?m(c) and in the size bands ?4 ?m(c), ?6 ?m(c), and ?14 ?m(c). Note 1:?ASTM and military specification fuels falling within
the scope of this test method include Specifications: D975 grades 1D and 2D, D1655, D3699, D4814 (see 14.1.1.1), D6751, D7467, distillate grades of D396 and D2880, MIL-DTL-83133, and
MIL-DTL-16884.
Note 2:?For the purposes of this test method, water droplets
are counted as particles, and agglomerated particles are detected
and counted as a single larger particle. Dirt includes biological
particles. Although the projected area of a particle is measured,
this is expressed as the diameter of a sphere for the purposes of
this test method.
Note 3:?The notation (c), used with particle sizes, is used to
denote that the apparatus has been calibrated in accordance with
ISO 11171. Strictly this only applies to particles up to 50
?m.
Note 4:?This test method may be used for particle sizes bands
up to 100 ?m(c), however the precision has only been determined for
the size bands ?4 ?m(c), ?6 ?m(c), and ?14
?m(c). All measurements are per millilitre.
1.2?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.12.2024 (Počet položek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.