Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D7448-16

Standard Practice for Establishing the Competence of Laboratories Using ASTM Procedures in the Sampling and Analysis of Coal and Coke (Withdrawn 2024)

Automaticky přeložený název:

Standardní postupy pro zřízení způsobilosti laboratoří podle normy ASTM procedury při odběru vzorků a analýzy uhlí a koksu

NORMA vydána dne 1.3.2016

Jazyk
Provedení	Elektronické PDF - 2 005.90 Kč Tištěné - 2 005.90 Kč
Dostupnost	SKLADEM
Cena	2005.90 Kč bez DPH
2 005.90 Kč

Informace o normě:

Označení normy: ASTM D7448-16
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2016
Kód zboží: NS-636758
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Tuhá paliva

Anotace textu normy ASTM D7448-16 :

Keywords:

accuracy, competence, evaluation, laboratory, management, stability,, ICS Number Code 75.160.10 (Solid fuels)

Doplňující informace

Significance and Use

3.1 International standard ANSI/ISO/IEC 17025 promotes the use of documented accountability and quality control procedures to assure a laboratory and its clients that the laboratory can produce technically valid data and results in the routine performance of its sampling, sample preparation and testing activities.

3.2 A laboratory shall use ANSI/ISO/IEC 17025 to develop its quality system. Clause 4 of ANSI/ISO/IEC 17025 specifies the requirements for sound management. Clause 5 of ANSI/ISO/IEC 17025 specifies the requirements for technical competence for the type of tests or calibrations, or both the laboratory undertakes.

3.3 In addition to complying with the requirements of ANSI/ISO/IEC 17025, the Annex of this standard practice contains information that shall be considered important for the evaluation and operation of a competent Coal and Coke sampling or testing facility, or both. The information in this Annex is presented where it is not otherwise covered in ANSI/ISO/IEC 17025 or the applicable ASTM methods.

3.4 Laboratory clients, regulatory authorities, and accreditation bodies that recognize the competence of testing and calibration laboratories can use this standard practice as the basis for their evaluation.

3.5 The primary significance of this practice is to establish that for a laboratory to generate measurements traceable to SI units, it must:

3.5.1 Have a clear understanding of the work requested by the client.

3.5.2 Meet the quality system requirements of the internationally accepted ANSI/ISO/IEC 17025 standard.

3.5.3 Use test methods which have been shown to be traceable to SI units of measurement.

3.5.4 Be able to demonstrate that the laboratory is in statistical control at the time the measurements are made.

1. Scope

1.1 This practice specifies requirements to operate and evaluate the quality and management systems in a laboratory that provides services with respect to sample collection, sample preparation, or testing of coal, coke, and ash derived from coal or coke using ASTM standards that are under the jurisdiction of Committee D05 on Coal and Coke.

Note 1: The word “laboratory” is used throughout this practice when referring to an organization that provides services in coal sampling or testing, or both. It is recognized, however, that the word may not be appropriate to an organization that does not perform actual laboratory sample testing.

1.2 International standard ANSI/ISO/IEC 17025 shall be the governing document specifying requirements for management, technical competence and evaluation of a laboratory.

Note 2: An accrediting body or user of laboratory services can also impose technical or non-technical requirements not specifically addressed in ANSI/ISO/IEC 17025 provided they do not invalidate the requirements of ANSI/ISO/IEC 17025.

1.3 This practice is used to evaluate only those capabilities specifically claimed by a laboratory.

1.4 All percentages are percent mass fractions unless otherwise noted.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E2554-18e1	Standard Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method Using Control Chart Techniques (Includes all amendments and changes 10/7/2019).
D6172-98e1	Standard Test Method for Determining the Volume of Bulk Materials Using Contours or Cross Sections Created by Direct Operator Compilation Using Photogrammetric Procedures
17025
5725-6	Accuracy (Trueness and Precision) of Measurement Methods and Results--Part 6: Use in Practice of Accuracy Values
D5515-22	Standard Test Method for Determination of the Swelling Properties of Bituminous Coal Using a Dilatometer
5725-3
D121-15(2024)	Standard Terminology of Coal and Coke
D3174-12(2018)e1	Standard Test Method for Ash in the Analysis Sample of Coal and Coke from Coal (Includes all amendments and changes 9/17/2020).
D4239-18e1	Standard Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion (Includes all amendments and changes 10/31/2018).
D4749-87(1994)e1	Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size
D5061-19	Standard Test Method for Microscopical Determination of the Textural Components of Metallurgical Coke

Doporučujeme:

EviNor - Řízení a aktualizace českých norem

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.