Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic PlantingPřeložit název
NORMA vydána dne 1.6.2022
Označení normy: ASTM D7367/D7367M-22
Datum vydání normy: 1.6.2022
Kód zboží: NS-1066993
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
fiber mulch, hydraulic planting, water holding capacity,, ICS Number Code 65.020.20 (Plant growing)
|Significance and Use|
5.1?The meaning of the test is related to the manufacturing quality assurance and quality control and end use of the material, to determine characteristics of products. The water holding capacity of hydraulically applied mulches for hydraulic planting correlates directly with enhanced slurry and spray patterns by providing better soil/slurry binding ability, mixing ability in a tank, and rate of seed germination.
Note 1:?The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice does not in itself assure reliable results. Reliable results depend on many factors; Practice provides a means of evaluating some of those factors.
1.1?This quantitative test method determines the water holding capacity of fiber mulches, including wood, paper, and agriculturally derived and blended fiber mulches that are used for hydraulic seeding and planting. Results from this testing can be used as a quality assurance and/or quality control data for manufacturing processes.
1.2?There are no known limitations to this test method.
1.3?UnitsThe values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. Reporting of test results in units other than inch-pound shall not be regarded as nonconformance with this standard. The amount of test water is presented in mL and no other unit of measurement is given.
1.3.1?The gravitational system of inch-pound units is used when dealing with inch-pound units. In the system, the pound (lbf) represents a unit of force (weight), while the units for mass is slugs. The slug unit is not given, unless dynamic (F = ma) calculations are involved. This standard includes the gravitational system of inch-pound units and does not use/present the slug unit of mass.
1.3.2?The slug unit of mass is typically not used in commercial practice; that is, density, balances, and so on. Therefore, the standard unit for mass in this standard is either kilogram (kg) or gram (g), or both.
1.4?All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice .
1.4.1?The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering data.
1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Poslední aktualizace: 08.12.2023 (Počet položek: 2 860 157)
© Copyright 2023 NORMSERVIS s.r.o.