Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D7367-19e2
Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting (Includes all amendments And changes 7/11/2022).
Přeložit název
NORMA vydána dne 15.6.2019
Informace o normě:
Označení normy: ASTM D7367-19e2
Poznámka: NEPLATNÁ
Datum vydání normy: 15.6.2019
Kód zboží: NS-968557
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D7367-19e2 :
Keywords:
fiber mulch, hydraulic planting, water holding capacity,, ICS Number Code 65.020.20 (Plant growing)
Doplňující informace
| Significance and Use | ||||
|
5.1 The meaning of the test is related to the manufacturing quality assurance and quality control and end use of the material, to determine characteristics of products. The water holding capacity of hydraulically applied mulches for hydraulic planting correlates directly with enhanced slurry and spray patterns by providing better soil/slurry binding ability, mixing ability in a tank, and rate of seed germination. Note 1: The quality of the result produced by this standard is
dependent on the competence of the personnel performing it, and the
suitability of the equipment and facilities used. Agencies that
meet the criteria of Practice D3740 are generally considered capable of
competent and objective testing/sampling/inspection/etc. Users of
this standard are cautioned that compliance with Practice
D3740 does not in itself
assure reliable results. Reliable results depend on many factors;
Practice D3740 provides a
means of evaluating some of those factors.
|
||||
| 1. Scope | ||||
|
1.1 This quantitative test method determines the water holding capacity of fiber mulches, including wood, paper, and agriculturally derived and blended fiber mulches that are used for hydraulic seeding and planting. Results from this testing can be used as a quality assurance and/or quality control data for manufacturing processes. 1.2 There are no known limitations to this test method. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.4.1 The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering data. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
| 2. Referenced Documents | ||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
