Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Guide for Collecting Treatment Process Design Data at a Contaminated Site—A Site Contaminated with Chemicals of Interest
Přeložit název
NORMA vydána dne 1.1.2021
Označení normy: ASTM D7294-13(2021)
Datum vydání normy: 1.1.2021
Kód zboží: NS-1013167
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
assessment, environmental, hazardous waste, remediation, sampling, solid waste, wastewater,, ICS Number Code 71.020 (Production in the chemical industry)
Significance and Use | ||||||||||||||||||||||||||||||||||||||||||
4.1?This guide allows the decision maker to determine which remedial treatment processes are and are not applicable to remediate an area of soil, surface water, or ground water that contains contaminants of concern. 4.2?This guide provides the data to make cost comparisons of the remedial treatment processes. 4.3?Analysis of treatment process design data can often be performed at the site with field instruments and test kits. 4.4?Tables 1 and 2 are a guide to selecting and obtaining physical and chemical treatment process design data. Data marked with an X is needed to evaluate alternatives and select a remedial treatment process. Once the remedial process is selected, the additional data that are needed to design the selected remedial treatment process are marked with an O. It may be advisable to also collect the data marked with an O during the initial sampling event to minimize sampling trips to the site. 4.5?Tables 3 and 4 list laboratory and field methods for analyzing this data. More than one analytical method may be listed. The most suitable method must be chosen for each application. 4.6?This
guide does not address sampling for contaminants of concern and
sampling locations. See EM 200-1-2 Technical Project Planning (TPP)
under Engineering Manuals6
for information on sampling contaminants of concern. It is
recommended that the treatment process design sampling be
coordinated with the sampling for chemicals of concern to minimize
duplicate sampling and trips to the site.
4.7?This guide does not address physical and chemical properties related to contaminant transport. This is addressed in Guide D5730. 4.8?This guide does not address why the data is needed to evaluate each treatment technology. This information is addressed in the Federal Remediation Technologies Roundtable (FRTR) site at http://www.frtr.gov in the U.S. Army Corps of Engineers guidance documents at http://www.usace.army.mil/inet/usace-docs/ and the United Facilities Guide Specifications (UFGS) available at http://www.ccb.org/. 4.9?This guide does not address Quality Assurance / Quality Control (QA/QC) or sampling design strategy. See U.S. Army Corps of Engineers Engineering Regulation ER 1110-1-263 and Engineering Manual EM 200-1-31.1?This guide lists the physical and chemical treatment processes design data needed to evaluate, select, and design treatment processes for remediation of contaminated sites. This data is listed in Tables 1 and 2. Much of these data can be obtained and analyzed at the site with instruments and test kits. 1.2?It is recommended that this guide be used in conducting environmental site assessments and Remedial Investigations/Feasibility Studies (RI/FS) and selections of remedy in U.S. Code of Federal Regulations 40 CFR 300.430. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||
|
Poslední aktualizace: 13.11.2024 (Počet položek: 2 210 764)
© Copyright 2024 NORMSERVIS s.r.o.