Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Establishing Characteristic Values for Reinforced Glued Laminated Timber (Glulam) Beams Using Mechanics-Based ModelsPřeložit název
NORMA vydána dne 1.8.2020
Označení normy: ASTM D7199-20
Datum vydání normy: 1.8.2020
Kód zboží: NS-1003009
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
This practice covers mechanics-based models for calculating characteristic values for the strength and stiffness of reinforced structural glued laminated timbers (glulam). The mechanics-based analyses shall account for the following: (1) stress-strain relationships for wood laminations and reinforcement; (2) strain compatibility; (3) equilibrium; (4) variability of mechanical properties; (5) volume effects; (6) finger-joint effects; (7) laminating effects; and (8) stress concentrations at the termination of reinforcement in beams with partial length reinforcement. This practice also provides for minimum physical test requirements to validate mechanics-based models. A minimum set of performance-based durability test requirements for reinforced glulams is also herein described. Additional durability test requirements shall be considered in accordance with the specific end-use environment.
bending, characteristic value, composites, flexural, flexure, FRP, full-scale, glulam, laminated, layup, modulus, reinforcement, timber,, ICS Number Code 79.060.99 (Other wood-based panels)
1.1 This practice describes procedures for establishing the characteristic values for reinforced structural glued-laminated timber (glulam) beams using mechanics-based models and validated by full-scale beam tests. Glulam beams shall be manufactured in accordance with applicable provisions of ANSI A190.1.
1.2 This practice also describes a minimum set of performance-based durability test requirements for reinforced glulam beams, as specified in . Additional durability test requirements shall be considered in accordance with the specific end-use environment. provides an example of a mechanics-based methodology that satisfies the requirements set forth in this practice.
1.3 This practice is limited to procedures for establishing flexural properties (modulus of rupture, MOR, and modulus of elasticity, MOE) about the x-x axis of horizontally-laminated reinforced glulam beams.
1.4 The establishment of secondary properties, such as bending about the y-y axis, shear parallel to grain, tension parallel to grain, compression parallel to grain, and compression perpendicular to grain, for the reinforced glulam beams are beyond the scope of this practice.
Note 1: When the establishment of secondary properties is deemed necessary, testing according to other applicable methods, such as Test Methods and or analysis in accordance with Practice , may be considered.
1.5 Reinforced glulam beams subjected to axial loads are outside the scope of this practice.
1.6 Proper safety, serviceability, and adjustment factors including duration of load, to be used in design are outside the scope of this practice.
1.7 Evaluation of unbonded, prestressed, and shear reinforcement is outside the scope of this practice.
1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The mechanics-based model shall be permitted to be developed using SI or inch-pound units.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 08.12.2023 (Počet položek: 2 860 157)
© Copyright 2023 NORMSERVIS s.r.o.