Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D6923-18

Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine´Caterpillar 1R Test Procedure

Přeložit název

NORMA vydána dne 1.10.2018

Jazyk
Provedení	PDF - okamžité stažení - 2 935.10 Kč Tištěné - 2 935.10 Kč
Dostupnost	SKLADEM
Cena	2 935.10 Kč bez DPH
2 935.10 Kč

Informace o normě:

Označení normy: ASTM D6923-18
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2018
Kód zboží: NS-905716
Počet stran: 65
Přibližná hmotnost: 195 g (0.43 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Maziva, průmyslové oleje a odpovídající výrobky

Anotace textu normy ASTM D6923-18 :

Keywords:
Caterpillar 1R test procedure, oil consumption, piston deposits, single cylinder diesel oil test,, ICS Number Code 75.100 (Lubricants, industrial oils and related products)

Doplňující informace

Significance and Use

5.1 This is an accelerated engine oil test, performed in a standardized, calibrated, stationary single-cylinder diesel engine that gives a measure of (1) piston and ring groove deposit forming tendency, (1.1 This test method covers stressing an engine oil under modern high-speed diesel operating conditions and measures the oil's deposit control, lubrication ability, and resistance to oil consumption. It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exceptions—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing size, or where a sole source supplier is specified.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The following is the Table of Contents:

Scope

1

Referenced Documents

2

Terminology

3

Summary of Test Method

4

Significance and Use

5

Apparatus and Installation

6

Intake Air System

6.2.1

Exhaust System

6.2.2

Fuel System

6.2.3

Oil Consumption System

6.2.4

Engine Oil System

6.2.5

Engine Coolant System

6.2.6

Engine Instrumentation

6.2.7

Reagents and Materials

7

Oil Samples

8

Preparation of Apparatus

9

General Engine Assembly Practices

9.1

Complete Engine Inspection

9.2

Copper Component

9.3

Engine Lubricant System Flush

9.4

Engine Piston Cooling Jet

9.5

Engine Measurements and Inspections

9.6

Cylinder Head

9.7

Valve Guide Bushings

9.8

Fuel Injector

9.9

Piston and Rings

9.10

Cylinder Liner

9.11

Compression Ratio

9.12

Engine Timing

9.13

Engine Coolant System Cleaning Procedure

9.14

Calibration and Standardization

10

Test Cell Instrumentation

10.1

Instrumentation Standards

10.2

Coolant Flow

10.3

Fuel Injectors

10.4

Air Flow

10.5

Intake Air Barrel

10.6

Fuel Filter

10.7

Oil Scale Flow Rates

10.8

Test Stand Calibration

10.9

Re-calibration Requirements

10.9.1

Extending Test Stand Calibration Period

10.9.2

Test Run Numbering

10.10

Humidity Calibration Requirements

10.11

Calibration of Piston Deposit Raters

10.12

Procedure

11

Engine Break-in Procedure

11.1

Cool-down Procedure

11.2

Warm-up Procedure

11.3

Shutdowns and Lost Time

11.4

Periodic Measurements

11.5

Engine Control Systems

11.6

Engine Coolant

11.6.1

Engine Fuel System

11.6.2

Engine Oil Temperature

11.6.3

Exhaust Pressure

11.6.4

Intake Air

11.6.5

Post-Test Procedures

11.7

Piston Ring Side Clearances

11.7.1

Piston Ratings

11.7.2

Ring Gap End Increase

11.7.3

Cylinder Liner Wear

11.7.4

Cylinder Liner Bore Polish

11.7.5

Photographs

11.7.6

Calculation and Interpretation of Results

12

Test Validity

12.1

Calculations

12.4

Quality Index

12.4.1

Oil Consumption

12.4.2

Report

13

Forms and Data Dictionary

13.1

Test Validity

13.2

Report Specifics

13.3

Precision and Bias

14

Precision

14.1

Bias

14.2

Keywords

9.11.1

Annexes

Engine and Parts Warranty

Annex A1

Instrument Locations, Measurements and Calculations

Annex A2

Cooling System Arrangement

Annex A3

Intake Air Mass Flow Sensor Installation

Annex A4

Fuel System Design and Required Components

Annex A5

Oil System

Annex A6

Additional Report Forms

Annex A7

Engine Assembly and Inspection Information

Annex A8

Flushing Instructions and Apparatus

Annex A9

Warm-up, Cool-down and Testing Conditions

Annex A10

Piston and Liner Rating Modifications

Annex A11

Return Goods Authorization Claim Form

Annex A12

Appendixes

Various Examples of Supplemental Information for Reference Purposes

Appendix X1

Safety

Appendix X2

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D235-22	Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
D445-23	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D5967-21	Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
D5966-22	Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine
D524-15(2019)	Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products
D5844-98	Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID) (Withdrawn 2003)
D5862-09	Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine (Withdrawn 2009)
D5302-01a	Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions (Withdrawn 2003)
D5185-18	Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
D4863-13	Standard Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants (Withdrawn 2022)
D6202-02	Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine (Withdrawn 2009)
D6594-20e1	Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 ?C (Includes all amendments and changes 6/22/2022).
D6681-23	Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E344-23	Terminology Relating to Thermometry and Hydrometry
G40-22a	Standard Terminology Relating to Wear and Erosion (Includes all amendments and changes 11/11/2022).
ASTM Deposit Rating Manual 20	(formerly CRC Manual 20) For Stock #TMCMNL20, visit the ASTM website, www.astm.org, or contact ASTM International Customer Service at service@astm.org.
SAE J183	Engine Oil Performance and Engine Service Classification Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.
D4052-22	Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D3524-14(2020)	Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
D4175-23a	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants (Includes all amendments and changes 12/21/2023).
D4485-22e1	Standard Specification for Performance of Active API Service Category Engine Oils (Includes all amendments and changes 12/8/2022).
D4739-23	Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
D3338-08	Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D664-18e2	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration (Includes all amendments and changes 1/4/2019).
D976-21e1	Standard Test Method for Calculated Cetane Index of Distillate Fuels (Includes all amendments and changes 2/23/2023).
D1298-12b(2017)e1	Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method (Includes all amendments and changes 3/14/2023).
D1319-20a	Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption (Includes all amendments and changes 9/14/2020).
D613-24	Standard Test Method for Cetane Number of Diesel Fuel Oil
D2500-23	Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
D2622-21	Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2709-22	Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
D86-23ae1	Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Includes all amendments and changes 2/9/2024).
D93-20	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D97-17b(2022)	Standard Test Method for Pour Point of Petroleum Products (Includes all amendments and changes 11/29/2022).
D130-19	Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

Doporučujeme:

nody.cz - Splňte si svůj sen o vlatsním e-shopu