Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D6923-03

Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine-Caterpillar 1R Test Procedure

Automaticky přeložený název:

Standardní zkušební metoda pro hodnocení Oleje motoru ve vysoké rychlosti , jednoválec Vznětový motor Caterpillar - 1R Zkušební postup

NORMA vydána dne 10.6.2003

Jazyk
Provedení	Online zabezpečené PDF - 3 007.40 Kč Tištěné - 3 007.40 Kč
Dostupnost	SKLADEM
Cena	3007.40 Kč bez DPH
3 007.40 Kč

Informace o normě:

Označení normy: ASTM D6923-03
Poznámka: NEPLATNÁ
Datum vydání normy: 10.6.2003
Kód zboží: NS-37015
Počet stran: 63
Přibližná hmotnost: 189 g (0.42 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM D6923-03 :

Keywords:

Caterpillar 1R test procedure, oil consumption, piston deposits, single cylinder diesel oil test, ICS Number Code 75.100 (Lubricants, industrial oils and related products)

Doplňující informace

1. Scope

1.1 This test method covers stressing an engine oil under modern high-speed diesel operating conditions and measures the oil's deposit control, lubrication ability, and resistance to oil consumption. It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine.⁴

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. Being an engine test method, this test method does have definite hazards that require safe practices (see Appendix X2 on Safety).

1.4 The following is the Table of Contents:

Scope	1
Referenced Documents	2
Terminology	3
Summary of Test Method	4
Significance and Use	5
Apparatus and Installation	6
Intake Air System	6.2.1
Exhaust System	6.2.2
Fuel System	6.2.3
Oil Consumption System	6.2.4
Engine Oil System	6.2.5
Engine Coolant System	6.2.6
Engine Instrumentation	6.2.7
Reagents and Materials	7
Oil Samples	8
Preparation of Apparatus	9
General Engine Assembly Practices	9.1
Complete Engine Inspection	9.2
Copper Component	9.3
Engine Lubricant System Flush	9.4
Engine Piston Cooling Jet	9.5
Engine Measurements and Inspections	9.6
Cylinder Head	9.7
Valve Guide Bushings	9.8
Fuel Injector	9.9
Piston and Rings	9.10
Cylinder Liner	9.11
Compression Ratio	9.12
Engine Timing	9.13
Engine Coolant System Cleaning Procedure	9.14
Calibration and Standardization	10
Test Cell Instrumentation	10.1
Instrumentation Standards	10.2
Coolant Flow	10.3
Fuel Injectors	10.4
Air Flow	10.5
Intake Air Barrel	10.6
Fuel Filter	10.7
Oil Scale Flow Rates	10.8
Test Stand Calibration	10.9
Re-calibration Recquirements	10.9.1
Extending Scale Calibration Period	10.9.2
Test Run Numbering	10.10
Humidity Calibration Recquirments	10.11
Calibration of Piston Raters	10.12
Procedure	11
Engine Break-in Procedure	11.1
Cool-down Procedure	11.2
Warm-up Procedure	11.3
Shutdowns and Lost Time	11.4
Periodic Measurements	11.5
Engine Control Systems	11.6
Engine Coolant	11.6.1
Engine Fuel System	11.6.2
Engine Oil Temperature	11.6.3
Exhaust Pressure	11.6.4
Intake Air	11.6.5
Post-Test Procedures	11.7
Piston Ring Side Clearance	11.7.1
Piston Ratings	11.7.2
Ring Gap End Increase	11.7.3
Cylinder Liner Wear	11.7.4
Cylinder Liner Bore Polish	11.7.5
Photographs	11.7.6
Calculation and Interpretation of Results	12
Test Validity	12.1
Calculations	12.4
Quality Index	12.4.1
Oil Consumption	12.4.2
Report	13
Forms and Data Dictionary	13.1
Test Validity	13.2
Report Specifics	13.3
Precision and Bias	14
Precision	14.1
Bias	14.2
Keywords	15
Annexes
Engine and Parts Warranty	Annex A1
Instrument Locations, Measurements and Calculations	Annex A2
Cooling System Arrangement	Annex A3
Intake Air Mass Flow Sensor Installation	Annex A4
Fuel System Design and Recquired Components	Annex A5
Oil System	Annex A6
Additional Report Form	Annex A7
Engine Assembly and Inspection Information	Annex A8
Flushing Instructions and Apparatus	Annex A9
Warm-up, Cool-down and Testing Conditiions	Annex A10
Piston and Liner Rating Modifications	Annex A11
Return Goods Authorization Claim Form	Annex A12
Appendixes
Various Examples of Supplemental Information for Reference Purposes	Appendix X1
Safety	Appendix X2

2. Referenced Documents

D235-22	Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
D445-26	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D5967-21	Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
D5966-22	Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine
D524-15(2025)e1	Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products (Includes all amendments and changes 8/11/2025).
D5844-98	Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID) (Withdrawn 2003)
D5862-09	Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine (Withdrawn 2009)
D5302-01a	Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions (Withdrawn 2003)
D5185-26	Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
D4863-13	Standard Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants (Withdrawn 2022)
D6202-02	Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine (Withdrawn 2009)
D6594-26	Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C
D6681-23	Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E344-26a	Terminology Relating to Thermometry and Hydrometry (Includes all amendments and changes 4/21/2026).
G40-25a	Standard Terminology Relating to Wear and Erosion (Includes all amendments and changes 12/8/2025).
ASTM Deposit Rating Manual 20	(formerly CRC Manual 20) For Stock #TMCMNL20, visit the ASTM website, www.astm.org, or contact ASTM International Customer Service at service@astm.org.
SAE J183	Engine Oil Performance and Engine Service Classification Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.
D4052-22	Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D3524-14(2020)	Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
D4175-24e2	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants (Includes all amendments and changes 6/9/2026).
D4485-24	Standard Specification for Performance of Active API Service Category Engine Oils
D4739-26	Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
D3338-08	Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D664-24	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
D976-21e1	Standard Test Method for Calculated Cetane Index of Distillate Fuels (Includes all amendments and changes 2/23/2023).
D1298-24	Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
D1319-26	Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
D613-26	Standard Test Method for Cetane Number of Diesel Fuel Oil
D2500-23	Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
D2622-26	Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2709-22	Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
D86-23ae2	Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Includes all amendments and changes 11/4/2024).
D93-26	Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D97-17b(2022)	Standard Test Method for Pour Point of Petroleum Products (Includes all amendments and changes 11/29/2022).
D130-26	Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

Doporučujeme:

EviZak - všechny zákony včetně jejich evidence na jednom místě

Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !

Chcete vědět více informací? Podívejte se na tuto stránku.