ASTM C1536-10
ASTM C1589/C1589M-14..
ASTM C1620-12
ASTM C1642-07
ASTM C1643-14
ASTM C1735-11
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D6622-01(2009)
Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
Automaticky přeložený název:
Standardní Pokyny pro použití plně dodržovány Hot-Aplikovaná Reinforced hydroizolačních systémů
NORMA vydána dne 1.1.2009
Informace o normě:
Označení normy: ASTM D6622-01(2009)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.1.2009
Kód zboží: NS-35927
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D6622-01(2009) :
Keywords:
application, asphalt, coal tar pitch, modified bitumen, polymer-modified bitumen sheet, rubberized asphalt waterproofing, waterproofing, Application--roofing/waterproofing material, Fully-adhered waterproofing systems, Reinforced roofing/waterproofing materials, Waterproofing materials/applications, ICS Number Code 91.100.50 (Binders. Sealing materials)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
This guide outlines general procedures and precautions for the application of fully adhered hot-applied built-up reinforced waterproofing systems. This guide is not all inclusive and is intended only to supplement detailed instructions from designers, and the recommendations of manufacturers. Manufacturers of some of the systems addressed by this guide require proprietary products and special procedures not described in this guide. Manufacturers' recommendations should therefore be considered in the application of this guide. For design guidelines, consult Guide C 981. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces. 1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Podobné normy:
Historická
1.6.2010
Historická
1.4.2014
Historická
1.6.2012
Historická
1.7.2007
Historická
1.6.2014
Historická
15.8.2011
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
