Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM D6616-07(2012) 1.11.2012 náhled

Doplňující informace

ASTM D6616-07(2012)

Standard Test Method for Measuring Viscosity at High Shear Rate by Tapered Bearing Simulator Viscometer at 100°C

Automaticky přeložený název:

Standardní zkušební metoda pro měření viskozity při vysoké smykové rychlosti by Kuželová ložiska Simulator viskozimetru při 100 ° C

NORMA vydána dne 1.11.2012

Jazyk
Provedení	PDF - okamžité stažení - 2 214.70 Kč Tištěné - 2 214.70 Kč
Dostupnost	SKLADEM
Cena	2 214.70 Kč bez DPH
2 214.70 Kč

Informace o normě:

Označení normy: ASTM D6616-07(2012)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2012
Kód zboží: NS-35900
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Měření objemu, hmotnosti, hustoty, viskozity

Anotace textu normy ASTM D6616-07(2012) :

Keywords:

dynamic viscosity, high shear rate viscosity, high shear rate viscosity at 100°C, high shear viscosity, high temperature viscosity, rotational viscometer, Tapered Bearing Simulator Viscometer, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)

Doplňující informace

Significance and Use

5.1 Viscosity at the shear rate and temperature of this test method is thought to be particularly representative of bearing conditions in large medium speed reciprocating engines as well as automotive and heavy duty engines operating in this temperature regime.

5.2 The importance of viscosity under these conditions has been stressed in railroad specifications.

1. Scope

1.1 This test method covers the laboratory determination of the viscosity of engine oils at 100°C and 1·10⁶s ^–1 using the Tapered Bearing Simulator (TBS) viscometer.²

1.2 The Newtonian calibration oils used to establish this test method range from approximately 5 to 12 mPa·s (cP) at 100°C and either the manual or automated protocol was used by each participant in developing the precision statement. The viscosity range of the test method at this temperature is from 1 mPa·s (cP) to above 25 mPa·s (cP), depending on the model of TBS.

1.3 The non-Newtonian reference oil used to establish the shear rate of 1·10⁶s^–1 for this test method has a viscosity of approximately 10 mPa·s at 100°C.

1.4 Application to petroleum products other than engine oil has not been determined in preparing the viscometric information for this test method.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. This test method uses the milliPascal second (mPa·s) as the unit of viscosity. This unit is equivalent to the centiPoise (cP), which is shown in parentheses.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D4683-20	Standard Test Method for Measuring Viscosity of New and Used Engine Oils at High Shear Rate and High Temperature by Tapered Bearing Simulator Viscometer at 150 °C
D4741-21	Standard Test Method for Measuring Viscosity at High Temperature and High Shear Rate by Tapered-Plug Viscometer