Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D6524/D6524M-16(2021)
Standard Test Method for Measuring the Resiliency of Turf Reinforcement Mats (TRMs)
Přeložit název
NORMA vydána dne 1.5.2021
Informace o normě:
Označení normy: ASTM D6524/D6524M-16(2021)
Datum vydání normy: 1.5.2021
Kód zboží: NS-1024147
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D6524/D6524M-16(2021) :
Keywords:
recovery, resiliency, thickness, turf reinforcement mat, TRM,, ICS Number Code 65.020.20 (Plant growing)
Doplňující informace
| Significance and Use | ||||||
|
5.1?Resiliency may be used to control the quality of many TRMs. Resiliency may be indicative of a TRM's ability to retain original configuration after exposure to the stresses which may be exerted during manufacture, shipping, and installation. Resiliency is not generally indicative of field performance. 5.2?The resiliency of TRMs may vary considerably depending on the pressure applied to the specimen during loading cycles. To minimize variation, specific sample size and applied pressure are indicated in this test method to ensure all results are comparable. 5.3?To determine the effect of different pressure loadings on the final thickness of TRMs, use this test method. 5.4?This test method may be used for acceptance testing of commercial shipments of TRMs, but caution is advised since information on between-laboratory precision is incomplete. Comparative tests in accordance with 5.4.1 may be advisable. 5.4.1?In a case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are formed from a lot of material of the type in question. The test specimens should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's Note 1:?The user should be aware that the compressibility of the materials, their rebound characteristics, and the like will also be affected by the thickness of the TRMs following the time when they are rolled up on rolls shipped and stored. |
||||||
| 1. Scope | ||||||
|
1.1?This test method covers the resiliency or recovery of turf reinforcement mats (TRMs) after they have been subjected to three cycles of loading at 689 kPa [100 psi] for 1 min/per cycle. 1.2?This test method does not provide resiliency values for TRMs under variable normal compressive stresses. This test method determines nominal resiliency. 1.3?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Doporučujeme:
