Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints
Přeložit název
NORMA vydána dne 1.1.2019
Označení normy: ASTM D6478-10(2019)
Datum vydání normy: 1.1.2019
Kód zboží: NS-910850
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Karosérie a součásti karosérie silničních vozidel
Textilní tkaniny
Keywords:
airbag, fabric, inflatable restraint, packability, packing, volume,, ICS Number Code 43.040.60 (Bodies and body components), 59.080.30 (Textile fabrics)
Adjunct to D6478 Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints
Vybrané provedení:Adjunct to D6478 Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints
Vybrané provedení:Significance and Use | ||||||||||||||
5.1 This test method is useful for determining the specific packability of uncoated and coated airbag fabrics. Fabric packability is an important factor in the design of airbag modules due to their inherent spacial constraints. 5.2 A folded specimen exhibits better specific packability if it occupies a lower total volume at the specified loads compared to another specimen. 5.3 The time required to test one sample (four specimens from the same lot of fabric) is approximately 1.5 h using this test method. Due to the length of time required by this test method to perform a single test, this test method is most suitable for use in design and development analysis or for inclusion in a list of required tests conducted for annual certification of an airbag fabric. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This test method covers procedures for determining the ability to fold and pack fabrics used for inflatable restraints using an index of specific packability. 1.2 Procedures in this test method describe operator techniques that must be followed closely to obtain repeatable and accurate results. Since these techniques are difficult to convey in writing, supplemental training for operators is required. A training video is available from ASTM (see Adjuncts ADJD6478 and ADJD6478A). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Procedures and apparatus other than those stated in this practice may be used as agreed upon between the purchaser and the supplier with specific deviations from this practice acknowledged in the report. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 01.11.2024 (Počet položek: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.