Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D6168-97e1
Standard Guide for Selection of the Minimum Set of Data Elements Required to Identify Locations Chosen for the Field Collection of Information to Describe Soil, Rock, and Their Contained Fluids (Includes all amendments And changes 8/16/2017).
Automaticky přeložený název:
Standardní Průvodce pro výběr minimálního souboru datových prvků potřebných k identifikaci umístění zvoleného pro pole sběru informací k popisu půdy , Rock , a uzavřeného tekutin
NORMA vydána dne 10.9.1997
Informace o normě:
Označení normy: ASTM D6168-97e1
Poznámka: NEPLATNÁ
Datum vydání normy: 10.9.1997
Kód zboží: NS-34079
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM D6168-97e1 :
Keywords:
coordinates, geoscience, investigation, geoscinece location, key data elements, rock, soil, underground fluids, ICS Number Code 13.080.01 (Soil quality in general)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This guide covers factors to consider
for the selection of the minimum set of data elements required for
the accurate location and cataloging of information collected for
geological science (geoscience) investigations, which includes
geoecology. 1.2 A unique geoscience data location, on
or below the earth's surface, can be described by X, Y, and Z
coordinates and by that method establish the dimensional
relationship to data of a similar nature. Additional location
information needed depends upon the type of geoscience data
collection locality. Note 1-An example is the latitude and longitude in horizontal coordinates and the altitude (or elevation) in vertical distance of a ground-water location or site. Data collected at the site, for example, water levels, are measured by the vertical interval as referenced to the altitude. 1.2.2 Another type of location is described by finite X and Y coordinates that has multiple vertically positioned Z coordinates. This is equivalent to the location type described in 1.2.1, except that mulitple vertical dimensions are stated as Z coordinates, rather than vertical intervals. Note 2-An example of latitude, longitude, and multiple altitudes of a soil sampling location or site. Each altitude represents a different sampling position that has the same latitude and longitude coordinate. The upper and lower limit of a sampling interval can be expressed by altitudes. 1.2.3 Another type is a location described by finite X and Y coordinates with multiple Z coordinates that are not vertically oriented from X and Y coordinates. Note 3-An example is a slanted borehole where the top is at a different latitude and longitude coordinate than the sampling positions in the hole. Methods of describing these sampling points are: treat each position as a separate location with finite latitude, longitude, and altitude values; describe the horizontal deviation of the sampling point from the finite latitude and longitude coordinates at the top of the borehole. 1.2.4 Another type is a location with considerable horizontal dimension that cannot be described by a finite X and Y coordinate, however, a single Z coordinated may be acceptable. Note 4-Examples are sinkholes, waste disposal pits, septic systems, underground injection facilities, mines, archaelogical sites, and some ponds or lakes. These locations can be described by including additional information that gives the horizontal components of the location along with the latitude, longitude, and altitude coordinates or by multiple sets of X and Y coordinates that encompass the location. 1.3 Additional key data elements are
needed to simplify the identification and cataloging of the
geoscience data. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word "Standard" in the title of this document means only that the document has been approved through the ASTM consensus process. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
