Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D5948-05(2012)
Standard Specification for Molding Compounds, Thermosetting
Automaticky přeložený název:
Standardní specifikace pro lití sloučenin termosetická
NORMA vydána dne 1.10.2012
Informace o normě:
Označení normy: ASTM D5948-05(2012)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2012
Kód zboží: NS-33152
Počet stran: 20
Přibližná hmotnost: 60 g (0.13 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D5948-05(2012) :
Keywords:
diallyl phthalate plastics, epoxy plastics, melamine-formaldehyde plastics, molding compounds, phenolic plastics, plastics, polyester plastics, silicone resin molding compounds, ICS Number Code 83.040.01 (Raw materials for rubber and plastics in general)
Doplňující informace
| Significance and Use |
|
4.1 This specification is a revision of STD MIL-M-14H, Specification for Molding Compound, Thermosetting, retaining the MIL-M-14H material designations and property requirements while conforming to ASTM form and style. It is intended for qualification and batch acceptance for materials used by government and industry, and is intended as a direct replacement for MIL-M-14H. |
| 1. Scope |
|
1.1 This specification covers the basic properties of thermoset molding compounds and the test methods used to establish the properties. 1.2 Classification—Molding thermosetting plastic compounds shall be of the following resins and are covered by the individual specification sheets (see Resin |
|
Phenolic, cellulose filled |
|
Phenolic, mineral/glass filled |
|
Melamine |
|
Polyester |
|
Diallyl iso-phthalate |
|
Diallyl ortho-phthalate |
|
Silicone |
|
Epoxy |
1.3 Order of Precedence—In
the event of a conflict between the text of this specification and
the references cited in Section 2 (except for related specification
sheets), the text of this specification takes precedence. Nothing
in this specification, however, supersedes applicable laws and
regulations unless a specific exemption has been obtained.
1.4 The values stated in SI units are to be considered standard.
|
Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation (Includes all amendments and changes 3/23/2023). |
|
|
Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
|
|
Standard Guide for Calibration and Testing Laboratory Accreditation Systems General Requirements for Operation and Recognition (Withdrawn 2004) |
|
|
Standard Guide for Maintaining Test Methods in the User's Laboratory (Withdrawn 2009) |
|
|
Standard Test Method for Corrosivity Index of Plastics and Fillers |
|
|
DDC AD 297457 |
Procedure for Determining Toxicity of Synthetic Compounds Available from National Technical Information Service (NTIS), U.S. Department of Commerce, 5285 Port Royal Rd., Springfield, VA 22161. |
|
Standard Guide for Categorizing Fields of Capability for Laboratory Accreditation Purposes (Withdrawn 2002) |
|
|
UL 94 |
Tests for Flammability of Plastic Materials for Parts in Devices and Appliances |
|
Standard Practice for Conditioning Plastics for Testing |
|
|
Standard Test Method for Tensile Properties of Plastics |
|
|
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
|
|
Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies |
|
|
Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
|
|
Standard Test Method for Water Absorption of Plastics |
|
|
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023). |
|
|
Standard Test Method for Compressive Properties of Rigid Plastics |
|
|
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
|
|
Practice for Compression Molding Test Specimens of Phenolic Molding Compounds (Withdrawn 1992) |
|
|
Standard Terminology Relating to Plastics |
|
|
Standard Practice for Transfer Molding Test Specimens of Thermosetting Compounds |
|
|
Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds |
|
|
Standard Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials |
|
|
Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials (Includes all amendments and changes 2/2/2022). |
