Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and External Calibration (Includes all amendments And changes 6/14/2019).
Automaticky přeložený název:
Standardní zkušební metoda pro stopové nečistoty v monocyklických aromatických uhlovodíků plynovou chromatografií a externí kalibrace
NORMA vydána dne 1.2.2015
Označení normy: ASTM D5917-15e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.2.2015
Kód zboží: NS-615038
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
aromatics, external standard, gas chromatography, impurities, purity, p-xylene, toluene, xylenes,, ICS Number Code 71.040.50 (Physicochemical methods of analysis), 71.080.15 (Aromatic hydrocarbons)
Significance and Use | ||||||||||||||||||||||||||||||||
5.1 Determining the type and amount of hydrocarbon impurities remaining from the manufacture of toluene, mixed xylenes, and p-xylenes used as chemical intermediates and solvents is often required. This test method is suitable for setting specifications and for use as an internal quality control tool where these products are produced or are used. Typical impurities are: alkanes containing 1 to 10 carbons atoms, benzene, toluene, ethylbenzene (EB), xylenes, and aromatic hydrocarbons containing nine carbon atoms. 5.2 Purity is commonly reported by subtracting the determined expected impurities from 100.00. However, a gas chromatographic analysis cannot determine absolute purity if unknown or undetected components are contained within the material being examined. 5.3 This test method is similar to Test Method D2360, however, interlaboratory testing has indicated a bias may exist between the two methods. Therefore the user is cautioned that the two methods may not give comparable results. |
||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||
1.1 This test method covers the determination of the total nonaromatic hydrocarbons and trace monocyclic aromatic hydrocarbons in toluene, mixed xylenes, and 1.2 Total aliphatic hydrocarbons containing 1 through 10 carbon atoms (methane through decanes) can be detected by this test method at concentrations ranging from 0.001 to 2.500 weight %. 1.2.1 A small amount of benzene in mixed xylenes or 1.3 Monocyclic aromatic hydrocarbon impurities containing 6 through 10 carbon atoms (benzene through 1.4 In determining the conformance of the test results to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statement, see Section 9. |
||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||
|
Poslední aktualizace: 29.04.2024 (Počet položek: 2 896 215)
© Copyright 2024 NORMSERVIS s.r.o.