Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D5249-10(2021)
Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland Cement Concrete and Asphalt Joints
Přeložit název
NORMA vydána dne 1.5.2021
Informace o normě:
Označení normy: ASTM D5249-10(2021)
Datum vydání normy: 1.5.2021
Kód zboží: NS-1024054
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D5249-10(2021) :
This specification covers backer material, either in rod or strip form, for use with cold- and hot-applied joint sealant in portland-cement concrete or asphalt-pavement joints. Sealant backer material is available in three types: Type I, Type II, and Type III, and serves one or more of the following purposes: (1) limits the amount and depth of sealant applied to a joint, (2) acts as a barrier interface to prevent backside adhesion (bondbreaker), and (3) provides a form to assist the sealant in developing a shape factor. The material shall be easily compressed and installed in the joint reservoir and shall be heat resistant when used with hot-applied sealants. Physical properties of the material shall conform to the specified requirements for (1) density, (2) tensile strength, (3) water absorption, (3) compression deflection force, (4) compression recovery, (5) heat resistance, and (6) maximum shrinkage. The test specimen, test procedure, apparatus, and calculations for the physical properties enumerated are detailed.
Keywords:
ICS Number Code 91.100.50 (Binders. Sealing materials)
Doplňující informace
| 1. Scope | ||||||||||||||||||
|
1.1?This specification covers backer material for cold- and hot-applied joint sealant for use in portland cement concrete or asphalt pavement joints. 1.2?This specification establishes basic requirements for sealant backer material, either in rod or strip form, that can withstand the temperature of hot- or cold-applied sealants without excessive deformation. 1.3?Sealant backer material serves one or more of the following purposes: 1.3.1?Limits the amount and depth of sealant applied to a joint, 1.3.2?Acts as a barrier interface to prevent backside adhesion (bond breaker), and 1.3.3?Provides a form to assist the sealant in developing a shape factor. 1.4?The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information purposes only. 1.5?The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
