Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Vapor Pressure of Petroleum Products (Automatic Method) (Withdrawn 2012)
Automaticky přeložený název:
Standardní zkušební metoda pro tlak par ropných produktů ( Automatic metoda) (Withdrawn 2012 )
NORMA vydána dne 1.11.2007
Označení normy: ASTM D5190-07
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2007
Kód zboží: NS-30195
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
automated vapor pressure measurement, dry vapor pressure, gasoline, hydrocarbon-oxygenate blends, petroleum products, vapor pressure, Automated procedures petroleum products analysis, Calibration petroleum analysis instrumentation, Dry vapor pressure, Gasoline, Gasoline-oxygenate blends, Hydrocarbon-oxygenate blends, Petroleum products, Petroleum samples, Pressure testing petroleum products, Vapor pressure (VPx) petroleum products, ICS Number Code 75.080 (Petroleum products in general)
Significance and Use | ||||||||
Vapor pressure is an important physical property of volatile liquids. The vapor pressure of gasoline and gasoline-oxygenate blends is regulated by various government agencies. Specifications for volatile petroleum products generally include vapor pressure limits to ensure products of suitable volatility performance. This test method is more precise than Test Method D 4953. |
||||||||
1. Scope | ||||||||
1.1 This test method covers the determination of the total vapor pressure of air-containing, volatile, petroleum products. This test method is suitable for testing samples with boiling points above 0°C (32°F) that exert a vapor pressure between 7 and 172 kPa (1 and 25 psi) at 37.8°C (100°F) at a vapor-to-liquid ratio of 4:1. This test method is suitable for testing gasoline samples that contain oxygenates. No account is made of dissolved water in the sample. 1.1.1 Some gasoline-oxygenate blends may show a haze when cooled to 0 to 1°C. If a haze is observed in 8.5, it shall be indicated in the reporting of results. The precision and bias statements for hazy samples have not been determined (see Note 8). 1.2 This test method is suitable for the calculation of a dry vapor pressure equivalent (DVPE) by means of a correlation equation (see 13.1). The calculated DVPE very closely approximates the dry vapor pressure that would be obtained on the same material when tested in accordance with Test Method D 4953. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.3 through 7.5 and 9.2. |
||||||||
2. Referenced Documents | ||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.12.2024 (Počet položek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.