Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D5171-15(2020)
Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons
Přeložit název
NORMA vydána dne 1.2.2020
Informace o normě:
Označení normy: ASTM D5171-15(2020)
Datum vydání normy: 1.2.2020
Kód zboží: NS-984102
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Pokrývky hlavy. Oděvní doplňky. Připevňovací oděvní prostředky
Anotace textu normy ASTM D5171-15(2020) :
Keywords:
button, impact resistance, strength,, ICS Number Code 61.040 (Headgear. Clothing accessories. Fastening of clothing)
Doplňující informace
| Significance and Use | ||||||
|
5.1 This test method may be used to determine the ability of a button to resist breaking under impact, for example in pressing the end item, which could cause the button to fail. Note 1: In the development of this test method it was found
that the following factors influenced the ability of a button to
resist failure under impact conditions: resin formulation, shape
ligne size, thickness, number and spacing of holes. Buttons may
also pass this test but fail during the pressing of a garment due
to the presence of heat during pressing.
5.1.1 If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate rest results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.2 Test Method D5171 for the determination of the impact resistance of buttons may be used for acceptance testing of commercial shipments of buttons but caution is advisable since information is lacking on precision. |
||||||
| 1. Scope | ||||||
|
1.1 This test method covers the determination of impact resistance of plastic sew-through buttons. 1.2 The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may or may not be exact equivalents: therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
