Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D5048-14

Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame

Automaticky přeložený název:

Standardní zkušební metoda pro měření srovnávací Vypalování Charakteristika a Odolnost proti propálení z tuhého plastu za použití 125 mm Flame

NORMA vydána dne 1.5.2014

Jazyk
Provedení	PDF - okamžité stažení - 2 020.00 Kč Tištěné - 2 020.00 Kč
Dostupnost	SKLADEM
Cena	2 020.00 Kč bez DPH
2 020.00 Kč

Informace o normě:

Označení normy: ASTM D5048-14
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2014
Kód zboží: NS-29628
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Zápalnost a hořlavost materiálů a výrobků
Plastické hmoty obecně

Anotace textu normy ASTM D5048-14 :

Keywords:

burning characteristics, flammability, plastics, solid, resistance to burn-through, small-scale burning tests, vertical burning tests, ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products), 83.080.01 (Plastics in general)

Doplňující informace


Significance and Use
5.1 The test results represent afterflame plus afterglow time, in seconds, for a material under the conditions of the test. The test results for plaques also indicate whether or not the specified flame will burn through a material. 5.2 The effect of material thickness, colors, additives, deterioration, and possible loss of volatile components is measurable. 5.3 The burning characteristics vary with thickness. Compare test data with data for materials of similar thickness only. 5.4 The results serve as a reference for comparing the relative performance of materials and can be an aid in material selection. 5.5 In this test method, the specimens are subjected to specific laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it will not always be possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method.

1. Scope
1.1 This fire-test-response test method covers a small-scale laboratory procedure for determining the relative burning characteristics and the resistance to burn-through of plastics using small bar and plaque specimens exposed to a 125-mm (500-W nominal) flame. 1.2 This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment. 1.3 The classification system described in 1.4 If found to be appropriate, it is suitable to apply the requirements to other nonmetallic materials. Such application is outside the scope of this technical committee. 1.5 This test method is not intended to cover plastics when used as materials for building construction or finishing. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
D883-24	Standard Terminology Relating to Plastics
D3801-20a	Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position (Includes all amendments and changes 9/11/2020).
D5025-20a	Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials (Includes all amendments and changes 4/16/2020).
D5207-20	Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials
E176-24	Standard Terminology of Fire Standards
E691-23	Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
IEC?60695-11-20	Fire Hazard Testing-Part 11-20: Test Flames - 500 W Flame Test Methods