Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size (Includes all amendments and changes 12/9/2019).
Přeložit název
NORMA vydána dne 1.11.2019
Označení normy: ASTM D4749/D4749M-87(2019)e1
Datum vydání normy: 1.11.2019
Kód zboží: NS-978332
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
coal size, sieve, sieve analysis ,, ICS Number Code 75.160.10 (Solid fuels)
Significance and Use |
4.1 This test method concerns the sieving of coal into designated size fractions for the purpose of characterizing the material as to its particle size distribution for further processing or for commercial purposes. This is covered in Part A of this standard. Raw, as well as prepared (crushed, cleaned, or screened), coals can be tested by this test method. 4.2 This test method is applicable for all types of coals, except for pulverized coals (see Method D197) such as fed into steam boilers. Low rank coals, that is, lignites, subbituminous, and high volatile bituminous C, must be dried with caution and handled with care to minimize deterioration or size degradation during sieving. 4.3 This test method is applicable for the wet or dry-sieving of coal at sizes from 200 mm [8 in.] to 38 μm [No. 400 U.S.A. Standard]. Methods for sizing materials below 38 μm are outside the scope of this test method. Note 2: The sizing of material that passes the 38 μm sieve is
normally performed by optical microscopy, sedimentation,
centrifugation, light scattering or obfuscation, surface area
measurement, or other such methods. Subsieve techniques are also
used sometimes.
4.4 This test method also concerns the designation of a coal sample as to its upper (nominal top-size) and lower (nominal bottom-size) limiting sizes for the purpose of characterizing the material for further processing or for commercial purposes. This is covered in Part B of this test method. Anthracite coal is further designated by a one word descriptive term (see 14.4). 4.5 Enough material may not be collected by this test method to meet subsequent test procedures, such as washability analyses (Test Method D4371). |
1. Scope |
1.1 This test method covers procedures for determining the sieve analysis of coal and designating the size of coal from sieve analysis data. Raw as well as prepared (crushed, cleaned or screened) coals can be tested by this test method. 1.2 This test method explains how to designate coal sizes from the results of sieve analysis data in order to represent the condition of the coal as sold. In the case of special mixtures or coals with noncontinuous ranges of sizes, a sufficiently complete sieve analysis must be made to properly describe the size distribution. 1.3 This test method is not applicable for determining the sieve analysis nor for designating the size of pulverized coal. (See Note 1.) Size fractions down to and including 38 μm [No. 400 U.S.A. Standard Series] can be treated by the methods discussed in this test method. Methods for handling size fractions below 38 μm [No. 400] will be developed by this committee. Note 1: For powdered or pulverized coal as is fired into steam
boilers, refer to Test Method D197.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 28.04.2024 (Počet položek: 2 896 137)
© Copyright 2024 NORMSERVIS s.r.o.