Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D471-06e1
Standard Test Method for Rubber Property´Effect of Liquids (Includes all amendments And changes 12/31/2010).
Automaticky přeložený název:
Standardní zkušební metoda pro Rubber Property'Effect kapalin
NORMA vydána dne 1.10.2006
Informace o normě:
Označení normy: ASTM D471-06e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2006
Kód zboží: NS-28255
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM D471-06e1 :
Keywords:
elevated temperature, fluid immersion, liquid immersion, reference fuel, rubber articles, rubber products, service liquid, Accelerated aging/testing--rubber/related materials, Breaking strength/tenacity--rubber, Bursting strength--rubber, Change in length, Dimensional change, Elevated temperature tests--rubber, Elongation--rubber, Evaporation loss, Fluid immersion, Fuel oils, Fuels (test medias), Hardness tests, Immersion--rubber materials/applications, Liquids immersion--effect on rubber
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Certain rubber articles, for example, seals, gaskets, hoses, diaphragms, and sleeves, may be exposed to oils, greases, fuels, and other fluids during service. The exposure may be continuous or intermittent and may occur over wide temperature ranges. Properties of rubber articles deteriorate during exposure to these liquids, affecting the performance of the rubber part, which can result in partial failure. This test method attempts to simulate service conditions through controlled accelerated testing, but may not give any direct correlation with actual part performance, since service conditions vary too widely. It yields comparative data on which to base judgment as to expected service quality. This test method is suitable for specification compliance testing, quality control, referee purposes, and research and development work. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This test method covers the required procedures to evaluate the comparative ability of rubber and rubber-like compositions to withstand the effect of liquids. It is designed for testing: ( 1) specimens of vulcanized rubber cut from standard sheets (see Practice D 3182), (2) specimens cut from fabric coated with vulcanized rubber (see Test Methods D 751), or (3) finished articles of commerce (see Practice D 3183). This test method is not applicable to the testing of cellular rubbers, porous compositions, and compressed sheet packing, except as described in 11.2.2. 1.2 ASTM Oils No. 2 and No. 3, formerly used in this test method as standard test liquids, are no longer commercially available and in 1993 were replaced with IRM 902 and IRM 903, respectively (see Appendix X1 for details). 1.3 ASTM No. 1 Oil, previously used in this test method as a standard test liquid, is no longer commercially available and in 2005 was replaced with IRM 901; refer to , Footnote A, and Appendix X3 for details. 1.4 This test method includes the following: 1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
EviZak - všechny zákony včetně jejich evidence na jednom místě
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
