Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Corrosiveness and Oxidation Stability of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils
Automaticky přeložený název:
Standardní zkušební metoda pro korozní agresivity a oxidační stability hydraulických olejů, turbínový letecký motor, maziv a jiných vysoce rafinovaných olejů
NORMA vydána dne 1.7.2014
Označení normy: ASTM D4636-14
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2014
Kód zboží: NS-27978
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
hydraulic fluid, lubricant, oxidation stability, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Significance and Use | ||||||||||||||||||
4.1 This test method simulates the environment encountered by fully formulated lubricating fluids in actual service and uses an accelerated oxidation rate to permit measurable results to be obtained in a reasonable time. The use of metals provides catalytic reactive surfaces of those materials commonly found in real systems. The high temperature and air agitation help accelerate the oxidation reactions that are expected to occur. Moisture in the air adds another realistic condition that encourages oil breakdown by facilitating acid formation. 4.2 Interpretation of results should be done by comparison with data from oils of known field performance. The accelerated conditions likely will cause one or more of the following measurable effects: mass change and corroded appearance of some metals; change of viscosity; increase in acid number; measurable reaction products in the form of sludge; and mass loss of oil due to evaporation. 4.3 This test method is most suitable for oils containing oxidation and corrosion inhibitors. Without such ingredient(s), the severe test conditions will yield rather drastic changes to the oil. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 This test method covers the testing of hydraulic oils, aircraft turbine engine lubricants, and other highly refined oils to determine their resistance to oxidation and corrosion degradation and their tendency to corrode various metals. Petroleum and synthetic fluids may be evaluated using moist or dry air with or without metal test specimens. 1.2 This test method consists of a standard test procedure, an alternative Procedure 1, and an alternative Procedure 2. As there are variations possible with this test method, it will be up to the particular specification to establish the conditions required. In addition to temperature, the variables to specify if other than those of the standard procedure or alternative Procedure 1 or 2 are: test time, air flow and humidity, sample frequency, test fluid quantity, and metal specimen(s). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Exception—The values in parentheses in some of the figures are provided for information only for those using old equipment based on non-SI units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.5.2011
Historická
1.7.2011
Historická
1.12.2012
Historická
1.6.2012
Historická
1.12.2012
Historická
1.12.2012
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.