Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D4610-98(2021)
Standard Guide for Determining the Presence of and Removing Microbial (Fungal or Algal) Growth on Paint and Related Coatings
Přeložit název
NORMA vydána dne 1.11.2021
Informace o normě:
Označení normy: ASTM D4610-98(2021)
Datum vydání normy: 1.11.2021
Kód zboží: NS-1043772
Počet stran: 2
Přibližná hmotnost: 6 g (0.01 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D4610-98(2021) :
Keywords:
algals, bleaches, fungals, microbials, washes,, ICS Number Code 87.040 (Paints and varnishes)
Doplňující informace
| Significance and Use | ||||
|
3.1?Microbial growth is a major cause of discoloration and deterioration of paint films. This guide describes techniques used to distinguish fungi and algae from other surface contaminants. 3.2?Repainting a surface contaminated with fungi or algae generally causes more rapid infestation of the new paint than repainting a surface from which fungal or algal growth has been removed. In addition, poor adhesion, staining/bleeding, and many other problems may result. This guide describes methods for removing fungal or algal growth prior to repainting. Note 1:?It is extremely important that all steps and notes be
read and followed. In particular the washing steps outlined in
5.2.2 and 5.2.4 must be fully carried out, since
residual sodium hypochlorite (bleach) can cause many of the same
problems, or even loss of coloration after repainting, and residual
phosphate detergents can encourage further fungal and algal
growth.
Note 2:?This procedure is intended for use when recoating the
surface. Reports of using this procedure to remove fungi and algae
without recoating necessitate inclusion of a warning about the
adverse effects of bleach on a coating film. The oxidative effects
of bleach can degrade film properties, including particularly the
bleaching (loss of color) in films containing organic coloring
pigments (such as quinacridones, etc.), loss of gloss, chalking,
etc. A small patch must be tested prior to use of this procedure
for that purpose.
|
||||
| 1. Scope | ||||
|
1.1?This guide describes techniques used for determining the presence of fungal or algal growth on paint and related coatings and methods for removal of such growth prior to recoating. 1.2?The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
| 2. Referenced Documents | ||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
